HVAC, Electrical & Plumbing Services in Hinckley, OH

Replaced the toilet tank-to-bowl gasket and flapper, and cut out the corroded section of copper supply below the toilet, extending new copper up through the subfloor with a straight stop valve and new supply line. Also replaced the leaking copper and ProPress dryer gas drop with black iron piping and installed a new flexible gas connector.

Diagnosed a leaking toilet at the flush cycle and addressed the supply side by installing a new shut-off valve and replacing the supply line. Also inspected the gas dryer connection at the natural gas shutoff and replaced the short flexible gas connector with a new flex line to ensure a secure, leak-free connection.

Performed scheduled maintenance on a two-year-old Generac standby generator, including a visual inspection of the enclosure, transfer switch, and connections, which showed no damage, rust, or corrosion. Load-tested the starting battery with a digital battery analyzer, which returned 100% state of health and charge, 13.25V, and 714 CCA (rated 540 CCA), confirming the battery is in good condition and the unit is ready for service.

Responded to service call for Generac generator experiencing abnormal starting behavior. Upon arrival, performed diagnostic inspection of the unit and identified issues with the starting sequence. Inspected generator components including control panel, battery connections, and starter assembly. Checked fuel system components and verified proper oil levels. Tested unit operation and confirmed generator now starts and runs properly with normal startup sequence restored.

Completed comprehensive cooling maintenance on HVAC system. Inspected condenser coil and found significant accumulation of dirt, dust, and organic debris between fins, which can restrict airflow and reduce system efficiency. Noted outdoor debris including dried leaves around unit perimeter. Coil fins remained structurally intact throughout inspection, and all ventilation components were functioning as designed.

Completed full HVAC system installation including a new 90% efficiency furnace/air handler unit with integrated humidification system. Installed vertical air handler in garage utility area with proper electrical connections, condensate drainage system using PVC piping, and black condensate pump components mounted to unit face. Added AprilAire whole-home humidifier with dedicated water supply line and integrated ductwork connections using flexible metallic ducting with spiral-wrapped insulation tape. All electrical wiring, conduit, and low-voltage control circuits properly installed and terminated. System tested and operational upon completion.

Corrected electrical installation deficiencies identified during failed inspection of transfer switch system. Properly seated red wires fully under terminal lugs, ensured all conductors were stripped and inserted completely into clear tap connectors, and secured conduit runs with appropriate strapping. Sealed all LB conduit bodies and sealtight fittings to prevent air transfer into garage disconnects, bringing installation into compliance with electrical code requirements.

Completed routine maintenance and tune-up on a 5-year-old American Standard furnace. Performed comprehensive inspection of all system components, checked and cleaned burner assembly, verified proper gas pressure and combustion efficiency, inspected heat exchanger for cracks or deterioration, tested safety controls and limit switches, examined blower motor and lubricated as needed, replaced air filter, checked and cleaned flame sensor, verified proper condensate drain operation through PVC piping system, inspected electrical connections and wiring, tested thermostat operation and calibration, and confirmed system startup and shutdown sequences. All components found to be operating within manufacturer specifications with no immediate repairs required.

Installed dedicated 240-volt, 50-amp GFCI circuit for hot tub application per electrical estimate. Ran appropriate wiring and installed required ground fault protection to meet code requirements for outdoor spa equipment.

Conducted comprehensive HVAC estimate for air conditioning replacement at residential property. Evaluated existing Comfortmaker furnace system and associated components including humidifier, ductwork, and electrical connections in basement utility area. Documented current installation configuration with detailed photography showing furnace unit, PVC drainage lines, copper refrigerant lines, flexible ductwork, and electrical wiring for replacement planning purposes.

Responded to service call for Lennox AC unit making noise during startup. Upon inspection, found condenser coils heavily soiled with accumulated dirt, debris, and organic material restricting airflow. Cleared vegetation from around unit perimeter and cleaned condenser coils to restore proper operation and eliminate startup noise.

Completed MVP recurring cooling maintenance visit on 3-year-old HVAC system. Performed comprehensive inspection of air handler unit, including examination of control board and electrical connections. Accessed and evaluated air filter, which showed significant dust accumulation and discoloration indicating normal usage since last service interval. Inspected wiring harnesses, terminal connections, and circuit board components for proper operation and secure connections. All system components verified to be functioning within normal parameters for unit age and service history.

Conducted electrical estimate for Generac generator installation at residential property. Evaluated existing transfer switch already present on-site and assessed electrical panel configuration in attic space to determine compatibility and connection requirements. Inspected circuit breaker panel, existing wiring infrastructure, and available routing paths through exposed joists for proper integration of generator system. Documented current electrical setup including panel capacity, breaker arrangement, and wire management to provide accurate scope of work for generator installation project.

Responded to E1100 fault code indicating an overcrank condition on residential Generac backup generator. Inspected gas valve assembly and fuel delivery system, verified proper operation of electromagnetic coils and connections. Cycled generator under no-load conditions to confirm system returned to normal operation after fault reset.

Responded to service call for residential backup generator that could not be reset remotely. Upon arrival, confirmed unit had been inadvertently left in service mode following initial installation, preventing remote system access and operation. Accessed generator control panel, switched unit from service mode to automatic standby mode, and verified proper system functionality. Generator now operating correctly with remote reset capability restored.

Completed installation of a Lennox 90% AFUE furnace in basement mechanical room. Installed complete PVC venting system with proper pitch and support, configured all ductwork connections including supply and return plenums with insulated flexible duct runs, and established all necessary gas and electrical connections per manufacturer specifications. Installed Kidde carbon monoxide alarm in accordance with safety codes to provide proper monitoring for combustion appliances.

Completed comprehensive duct cleaning service for residential system with 14 vents. Accessed crawl space areas to thoroughly clean ductwork, removing accumulated dust, debris, and contaminants from supply and return lines. Documented pre-existing conditions including moisture staining on crawl space flooring and exposed structural elements to ensure complete system assessment.

Performed routine preventative maintenance descaling service on Rinnai tankless water heater in 5-year-old residential property. Isolated unit using cold water shut-off valve, connected descaling pump to service valves, and circulated descaling solution through heat exchanger to remove mineral buildup and scale deposits. Flushed system thoroughly with clean water, verified all connections at copper and CPVC piping, checked expansion tank pressure, and confirmed proper operation of all isolation valves including red and blue-handled service valves. Unit restored to normal operation with no reported issues or symptoms prior to service.

Responded to failed electrical inspection for Generac generator and transfer switch installation. Corrected code violations including separating unprotected service wires from feeder wires into separate raceways, properly strapping conduit and SER cable, replacing non-rated Romex connectors in wet locations with approved fittings, establishing proper grounding in garage disconnect with secure ground lug connections ensuring all wire strands seated under lugs, and installing connectors correctly into soft start controllers. All corrections made to meet electrical code requirements and pass inspection.

Completed heating maintenance tune-up on 16-year-old furnace system that was operating properly upon arrival. Performed comprehensive system inspection, tested all safety controls, verified proper airflow and temperature readings using digital measurement equipment, and inspected ductwork condition. System left in good working order with all components functioning within normal parameters.