HVAC, Plumbing & Electrical Solutions for Hudson, OH Homes

Completed comprehensive cooling system maintenance on residential air conditioning unit estimated at approximately 2 years old. Performed standard AC tune-up procedures including temperature diagnostics at the air handler test port (measured 45°F supply air temperature) and electrical testing at the outdoor condenser unit using digital multimeter to verify proper voltage and amperage. System operating within normal parameters with no deficiencies identified or repairs required.

Responded to complaint of loud noise from AC unit. Performed diagnostic assessment and took temperature measurements at ceiling level registering 50.9°F, indicating proper cooling function. Inspected accessible components and documented conditions for service records.

Completed installation of a 90% efficiency furnace and air conditioning system. Installed new electrical disconnect with FLNR 35 amp fuses rated at 250 volts, established proper electrical connections with color-coded wiring, and mounted outdoor condensing unit. Inside mechanical room, installed furnace unit with associated PVC condensate drainage system featuring multiple drain lines and proper pitch for water removal. Routed black flexible electrical conduit for system controls and power supply, installed safety float switch on drainage system, and established all necessary connections to existing ductwork. System tested and verified operational with all safety devices functioning properly.

Responded to no cooling complaint on four-year-old air conditioning system affecting entire home. Performed diagnostic testing using digital multimeter, measuring voltage at 147.9V at outdoor unit. Inspected ductwork in confined space, noting significant condensation present on metal surfaces at junction points. System evaluation revealed electrical parameters and refrigerant circuit operation to determine root cause of cooling failure and restore proper system function.

Performed camera inspection of main 4-inch kitchen drain line to trace routing and locate exterior exit point. Inspection revealed significant water damage to interior wall and ceiling materials with extensive brown staining, deteriorated drywall, and exposed plumbing infrastructure including vertical PVC drain line and associated piping. Documentation completed through photographic evidence showing chronic moisture intrusion, structural compromise, and potential mold presence to provide accurate assessment for necessary repair scope and quote development.

Installed dedicated electrical outlet for tankless water heater in utility area. Ran new circuit wiring through basement space to power unit, ensuring proper amperage and code compliance for the tankless water heating system.

Replaced a leaking 40-gallon tall water heater with a new Navien NPE-240A2 tankless water heater. Mounted the unit near the crawl space access opening for improved accessibility. Installed copper supply piping on both sides of the unit and routed PVC condensate drain line to existing floor drain behind furnace. Ran PVC exhaust and fresh air intake piping through crawl space to west exterior wall with proper termination and vent caps. Coordinated electrical outlet installation to provide dedicated power supply for tankless unit. All necessary parts were pre-staged prior to installation to ensure efficient completion of the retrofit.

Responded to customer complaints of excessive humidity causing window condensation on lower level and inadequate cooling on upper level. Upon inspection, discovered Lennox outdoor unit completely packed with dirt, dust, and debris that had accumulated to the point of obscuring all internal components including coils and mechanical parts. The severe blockage was restricting airflow and preventing proper heat exchange, causing system inefficiency and inability to maintain comfort levels throughout the home. Removed access panel and thoroughly cleaned condenser unit, extracting compacted debris from coil fins and interior cavity to restore proper airflow and system operation.

Responded to service call for cracked tee fitting on main gas line run. Removed the damaged tee fitting and replaced with approved elbow fitting, adapting connection back onto the 1-inch gas line supply run servicing HVAC system and water heater. Verified all connections for proper seal and tested system for gas leaks to ensure safe operation.

Responded to service call for 11-year-old furnace requiring heat exchanger evaluation. Performed visual inspection of unit and utilized camera equipment to inspect internal ductwork and heat exchanger components for cracks, corrosion, or failure indicators. Documented findings with photographic evidence and provided estimate for heat exchanger repair or replacement options to customer.

Responded to service call for stuck shower valve affecting two showers on the same water line. Accessed plumbing system through wall opening to inspect brass valve assembly and copper piping connections. Freed the seized valve mechanism, restored water flow to both shower fixtures, and verified proper operation of the system.

Responded to service call for 13-year-old air conditioning system experiencing short cycling every 20 seconds and failure to reach thermostat setpoint. Upon arrival, found condenser unit exterior heavily covered with dirt, organic debris, and biological growth indicating extended period without maintenance. Performed thorough cleaning of condenser coils and exterior surfaces to restore proper airflow and heat transfer efficiency. Addressed accumulated debris that was restricting airflow and causing unit to overheat and cycle prematurely. System tested after cleaning and confirmed proper operation with normal run cycles and adequate cooling to thermostat setpoint.

Responded to no cooling call on 15-year-old air conditioning system. Upon arrival, performed diagnostic inspection of outdoor condensing unit which showed signs of age and weathering with substantial dirt accumulation on exterior surfaces. Inspected electrical connections at unit, noting multiple wire terminations including ground, line voltage, and control wiring with wire nuts. Unit required further troubleshooting to identify root cause of cooling failure.

Responded to service call for reported leak on 4-year-old 50-gallon gas water heater. Upon inspection, discovered significant sediment and mineral deposit accumulation on top of unit around plumbing connections and vent assembly. Documented existing installation configuration including flexible stainless steel supply lines, brass fittings, and galvanized vent piping. Assessed water heater condition and verified leak source to determine appropriate repair or replacement recommendations for customer.

Completed installation of new flue piping for existing 90% efficiency furnace system as warranty follow-up work. Installed proper PVC venting components, secured all connections, and verified carbon monoxide detector placement for safe operation.

Completed scheduled MVP cooling maintenance visit on 2-year-old air conditioning system. Performed comprehensive inspection of blower wheel assembly, verified proper operation of fan blades and mounting hardware, and examined all internal components including circuit board, capacitor, and control modules. Inspected filter housing, checked electrical connections and wire harnesses, and confirmed all system components are functioning within normal parameters for continued reliable operation.

Responded to potential gas leak call and conducted thorough inspection of basement gas piping system. Performed visual examination of exposed gas lines, connections, and fittings in crawl space area, checking all joints, T-connections, and couplings for signs of damage or deterioration. Completed pressure test on gas system to verify integrity and confirm no active leaks present.

Completed MVP preventive maintenance cooling visit on 14-year-old air conditioning system. Inspected and tested dual element time-delay fuses rated at 45A 250V AC, verified proper electrical protection. Measured supply air temperature at 53.8°F, confirming adequate cooling performance and proper refrigerant charge for system age.

Replaced existing water heater with new 40-gallon short tank unit featuring a 10-year tank warranty. Installed new expansion tank on cold water supply line at the water heater and properly capped off the previous expansion tank that was connected behind the unit with the supply line. Per customer request, installed a drain pan beneath the new water heater for added protection. All copper supply lines, brass fittings, shut-off valves, and flue venting were properly connected and tested for safe operation.

Completed scheduled preventive maintenance cooling visit on 10-year-old air conditioning system. Replaced heavily soiled air filter with new pleated filter, removing significant dust and particulate buildup that had accumulated during the service period. Inspected control board and electrical connections, verifying all wire harnesses, circuit boards, and components were secure and functioning properly with no signs of damage or deterioration.