Blind & Sons: Full-Service HVAC, Plumbing & Electrical Experts in Ravenna, OH

Performed an on-site estimate for installation of a Kohler standby generator, including inspection of the existing main electrical panel to evaluate capacity, available breaker space, and transfer switch integration. Documented the panel's condition, noting crowded, disorganized conductor routing, dust and cobweb accumulation, and sagging wire bundles that should be addressed to support a code-compliant, reliable generator connection.

Performed a seasonal heating maintenance inspection on a 5-year-old Lennox upright gas furnace, including visual assessment of the cabinet, flue vent connection, and condensate pump and drain line. Inspected the control board and low-voltage wiring harness for secure connections and signs of overheating or wear, finding no frost, corrosion, or visible damage. Unit was left in good working condition with no deficiencies noted.

Performed annual heating maintenance and verified combustion performance using a Bacharach electronic combustion analyzer on the natural gas appliance. Readings were within normal operating range, with CO at 17 ppm, efficiency at 98.2%, CO2 at 7.6–7.7%, O2 at 7.4%, and stack temperature at 88°F, confirming safe and efficient operation.

Performed annual maintenance on a 12-year-old gas furnace, including a borescope inspection of the internal heat exchanger and cabinet areas to assess condition and check for debris or obstructions. Found the pleated air filter heavily loaded with dust and debris, restricting airflow, and removed it for replacement to restore proper system airflow and efficiency.

Replaced a 30-foot run of 1-1/2" copper high rough sewer line that had corroded through on the bottom, transitioning to the existing 1-1/2" ABS at both ends and securing the new piping with straps and J-hooks. Also replaced a section of the sump discharge line with new ABS piping and installed a new check valve to ensure proper one-way flow.

Inspected the reported basement water leak, tracing the supply and drain piping beneath the kitchen sink area through the exposed floor joists, including the copper supply lines and associated mechanical connections near the furnace and humidifier. No active leak, pipe perforation, corrosion, or water damage was found on the accessible copper piping or fittings, and the system was left in normal working condition.

Installed a single-head ductless mini-split heat pump system, mounting the outdoor condenser on a composite pad with bracket feet and the indoor air handler high on the garage wall. Ran and connected the refrigerant line set and control wiring between units, installed a service disconnect at the condenser, and completed the installation with a clean, secure finish.

Responded to a no-heat call on a Lennox EL297UH090XV36C gas furnace (under manufacturer warranty) where the blower was running but no heat was produced and multiple fault codes were displayed. Inspected the furnace, PVC intake/exhaust piping, ductwork, and the connected Aprilaire humidifier control, finding no visible frost, rust, or physical damage, and documented equipment condition with photos. Reviewed the fault code history and the prior no-heat visit to isolate the cause of the ignition/heat-call failure.

Responded to a leak reported near the water supply piping following a prior plumbing repair. Inspected the mechanical area, including the water softener and filtration system, copper supply lines, soldered joints, PEX piping, and PVC drain connections, and located the leak source and secured the affected connections. Verified the system held pressure with no remaining leaks and confirmed the area was dry.

Performed annual maintenance on a 7-year-old gas furnace, including inspection of the inducer assembly, pressure switch, hoses, and wiring harness. Noted corrosion and moisture staining on the cabinet floor beneath the pressure switch hoses, indicating possible condensate or heat-related exposure, and documented the condition with photos for further evaluation.

Performed annual preventive maintenance on a Generac standby generator, including visual inspection of the engine compartment, starter motor, wiring harness, split loom conduit, and throttle/governor linkage, all of which appeared in good condition with secure connections. Noted surface corrosion and staining on the enclosure's interior panel and recommended monitoring and treating the affected areas to prevent further deterioration. Advised that annual inspection is recommended to maintain reliable standby operation alongside the weekly exercise cycle.

Installed a complete split HVAC system consisting of an 80% AFUE gas furnace with matched evaporator coil and an outdoor air conditioning condenser. The condenser was set on a level pad with an exterior electrical disconnect and flexible conduit, and refrigerant lines were connected, insulated, and secured. The furnace was connected to the venting, condensate drain, and gas and electrical supplies, with the existing humidifier retained, and the system was commissioned for proper operation.

Performed annual maintenance on a New Yorker oil-fired boiler with a Beckett burner, including inspection of the burner assembly, fuel line, filter, and associated piping and controls. Conducted a combustion efficiency test with a Bacharach Fyrite analyzer, recording O2 at 6.5%, CO2 at 10.8%, CO at 27 ppm, and combustion efficiency of 85.6%, with the system operating within acceptable parameters.

Removed existing smoke detectors from their mounting bases, exposing the wiring harness connections at each location. Replaced the units with new smoke detectors, reconnecting the line, neutral, and interconnect conductors and securing each detector to its base. Tested each unit for proper operation.

Performed annual heating maintenance on a 3-year-old system, inspecting the blower assembly and finding a buildup of fine dust and debris on the squirrel-cage wheel and housing. Inspected the internal components with a probe, checking the gas valve/control area and the airflow-labeled access panel, and noted dirt accumulation on the panel surfaces and near the adjoining cable. Cleaned affected components to restore proper airflow and system efficiency.

Completed comprehensive duct cleaning service for residential HVAC system with 14 or fewer vents. Removed accumulated debris including organic matter, leaves, and dirt from ductwork and ventilation components. Cleaned interior duct surfaces and exhaust pathways to restore proper airflow and system efficiency.

Completed comprehensive MVP furnace maintenance inspection and servicing. Removed access panels to perform thorough internal examination of all critical components including blower motor assembly, control board, electrical connections, and wiring harnesses. Verified proper operation of all mechanical and electrical systems, inspected burner assembly, heat exchanger, and ventilation components. All components found to be in functional condition with normal operational wear, system reassembled and returned to service.

Completed scheduled MVP heating maintenance visit. Performed comprehensive system inspection including examination of burner assembly, blower motor, fan wheel, and linkage mechanisms. Documented equipment condition with photos showing gas valve linkage, damper components, and air intake assembly. All mechanical components operating within normal parameters. System tested and confirmed proper operation.

Installed a dedicated 20-amp circuit from main residence to detached garage using 1-1/4" PVC conduit buried approximately 24" deep to accommodate future electrical upgrades. Wired garage with 2 switches, 6 outlets (including 2 switched outlets for lighting control), and 1 exterior flood light fixture. Corrected electrical panel by replacing improperly sized breakers: removed one 2-pole 60-amp breaker and one tandem 15-amp breaker, installed two single-pole 15-amp breakers per code requirements. Replaced burnt outlet in basement and inspected associated wiring for damage or additional concerns. Work performed under permit with trench left open for municipal inspection approval prior to backfilling.

Completed installation of dryer vent system routing through garage space with exterior termination. Installed rigid metal ductwork through exterior wall penetration, properly sealed all openings with appropriate caulking material, and mounted weatherproof exterior vent hood with secure fastening to vinyl siding above foundation level.