Air Conditioning, Heating, Electrical & Plumbing Services in Tallmadge, OH

Responded to slow draining sewer line with bubbling noises in sinks and toilets following upstairs shower use. Inspected exterior sewer cleanout access point and found missing cap, which was causing improper venting and drainage issues. Cleared debris from cleanout area and restored proper system function.

Responded to gas leak identified at water heater connection point following initial gas line installation. Upon inspection, discovered heavily corroded and deteriorated black iron piping with significant rust, oxidation, and mineral deposits at threaded fittings and connections. Addressed the leak at the water heater gas line connection to ensure safe operation and compliance with gas company requirements.

Replaced main gas line from meter in front yard to residential structure. Excavated trench from meter location to home using mechanical trencher, installed new gas line secured to exterior of building, and penetrated through garage overhang into attic space to connect with existing appliance feed lines serving boiler and water heater. Installed proper fittings and transitions in attic crawlspace to tie into existing distribution system. Backfilled excavated trench and allowed to settle. Conducted complete system pressure test to verify integrity of installation and confirmed no leaks present throughout entire gas line system.

Completed MVP cooling maintenance visit on primary HVAC system. Inspected evaporator coil assembly and control board, confirming all components operational with normal wear patterns. Customer declined service on mini split unit during this visit.

Responded to service call for bathtub diverter malfunction where the tub spout diverter lever was stuck in the down position and unable to engage to redirect water flow to the shower head. Inspected the chrome tub spout assembly and diverter mechanism, confirmed the diverter was frozen due to mineral buildup and corrosion preventing proper operation. Successfully freed and restored functionality to the diverter system, allowing proper water diversion between tub spout and shower head.

Completed MVP cooling maintenance visit on 5-year-old Lennox HVAC system. Inspected furnace unit, humidifier assembly, and associated ductwork; verified proper operation of humidifier pad and airflow components. All equipment found in satisfactory working condition with normal dust accumulation for routine service interval.

Responded to service call for garbage disposal replacement. Removed existing failed disposal unit and installed new garbage disposal under kitchen sink, connecting to existing drain assembly and P-trap configuration. Verified proper electrical connection, tested unit operation, and confirmed no leaks in the system.

Replaced faulty sump pump check valve and rebuilt the discharge line section exiting the residence. Secured piping to wall with appropriate strapping to ensure proper drainage flow and prevent future movement. Work completed over two hours following parts delivery to shop.

Performed descaling maintenance on a 17-year-old Rinnai tankless water heater unit. Flushed the heat exchanger with descaling solution to remove mineral buildup, verified proper operation of all components, and confirmed unit was functioning within manufacturer specifications upon completion.

Responded to no heat call on one-year-old furnace system. Upon arrival, accessed unit and performed diagnostic inspection of internal components including blower assembly, control board wiring, and ignition system. Verified all electrical connections were secure and inspected copper refrigerant lines and condensate drainage system. System restored to proper heating operation and tested for normal cycling.

Responded to sump pump overflow and drainage blockage in 20-year-old residential property. Upon inspection, identified compromised sump pump system in basement with discharge pipe configuration issues and evidence of water intrusion around basin perimeter. Assessed exterior drainage concerns including significant standing water accumulation on patio area, indicating potential backflow or inadequate discharge routing. Cleared blockage from pump system, verified proper operation of discharge lines, and restored functionality to prevent further basement flooding and exterior water pooling.

Completed annual air conditioning maintenance and tune-up on a 4-year-old residential cooling system. Performed comprehensive inspection of all major components including blower motor assembly, refrigerant lines, and electrical connections. Examined control board circuitry and verified proper operation of outdoor discharge air sensor and integrated circuit components. Checked wire terminations and connections throughout the system, ensuring all wire nuts and harness connections were secure. Inspected copper refrigerant lines for proper insulation and connections to blower motor housing. Verified all safety labels and operational information were visible and legible. System tested and operating within normal parameters upon completion of maintenance service.

Responded to service call for non-operational sump pump with rising water levels in basement utility area. Upon arrival, inspected sump pump basin and found pump had failed, preventing proper drainage and allowing water accumulation in pit. Removed defective pump unit from basin and tested float switch mechanism, confirming mechanical failure. Installed replacement sump pump with appropriate horsepower rating for residential application. Connected discharge piping to existing white PVC vertical pipe running up wall. Verified all electrical connections were secure and properly grounded. Tested pump operation by filling basin and confirming automatic float activation and proper water discharge through existing drainage system. Pump cycled correctly and reduced water level as designed. Advised property occupant of extensive moisture damage and water staining visible on basement walls and floor, indicating history of water infiltration issues that may require additional waterproofing measu

Responded to gas service call for reported gas leak with gas supply shut off at roadside meter. Performed systematic leak detection inspection throughout property, checking all natural gas appliances, connections, and supply lines. Inspected interior gas piping at electrical panel area and exterior meter installation. Documented findings with photos and contacted property owner with results and recommendations for restoring gas service.

Completed MVP cooling maintenance on residential HVAC system. Performed comprehensive inspection of outdoor condensing unit, verified all refrigerant lines and electrical connections were secure and properly functioning, and inspected indoor air handler with pleated filter in place. All system components found to be in operational condition with no repairs required at this time.

Completed routine MVP heating maintenance visit on residential HVAC system. Performed comprehensive inspection of furnace mechanical components, condensate drainage system with PVC piping, and ductwork connections. Verified proper operation of Aprilaire whole-house humidifier unit including control settings, water supply connections, and electrical components to ensure optimal system performance for the heating season.

Performed inspection of outdoor condensing unit and identified significant dirt buildup on condenser coil affecting system efficiency. Recommended annual chemical cleaning of outdoor condenser to maintain peak performance and optimal heat transfer. Additionally recommended installation of surge protector on outdoor condenser to provide protection against electrical surges and voltage spikes that could damage compressor and electrical components.

Completed preventive maintenance cooling visit on outdoor HVAC unit. Inspected electrical components, capacitor, and wiring connections; all found to be in good working condition with proper organization and no signs of deterioration. Unit exterior showed normal weathering with system operating within manufacturer specifications.

Completed installation of new internal check valve and flow sensor on existing Navien 240a tankless water heater. Accessed internal components of the unit, integrated the flow sensor into the water supply line, and installed the check valve to prevent backflow and ensure proper system operation. All connections were secured with appropriate fittings, electrical connections were made to the control board, and the unit was tested to verify proper flow detection and valve function. The water heater was reassembled and returned to full operational status.

Responded to slow bathroom drain complaint at 62-year-old residential property. Accessed plumbing assembly beneath sink and inspected P-trap, drainage connections, and supply lines. Disassembled chrome P-trap to remove accumulated debris and buildup causing drainage restriction. Cleared blockage, reassembled all compression fittings, and tested drainage flow to confirm proper operation. All components reinstalled and system restored to normal function.