Air Conditioning, Heating, Electrical & Plumbing Services in Uniontown, OH

Upon arrival, inspected electrical junction box located in septic tank area and found water intrusion in the enclosure along with severely deteriorated wiring. All pump and float switch wires exhibited brittleness due to moisture exposure and age, creating potential safety hazards and system failure risks. Documented conditions with photographs showing the compromised control panel with multiple wire connections, circuit breakers, and contactors affected by the environmental conditions. Advised that complete wire replacement is necessary for all septic system electrical components to restore safe and reliable operation.

Completed scheduled MVP heating maintenance visit on 2-year-old system. Performed comprehensive system inspection including airflow verification through supply vents and electrical diagnostics. Measured resistance values on heating components, recording 53 ohms on tested circuits to verify proper operation. All components found operating within manufacturer specifications with no deficiencies noted.

Completed return trip to install VZ pro surge protector on residential HVAC air handler unit located in attic space. Surge protector installed using truck stock materials and wired into system electrical connections to provide equipment protection against voltage spikes.

Installed GFCI-protected electrical circuit for pool pump by hand-digging trench approximately 7-10 feet alongside foundation and deck structure. Installed copper bonding ring around pool perimeter with inline skimmer bond connection and proper pump bonding per NEC requirements. Set electrical post for pump disconnect, ran conduit and wiring through excavated trench, and completed all grounding and bonding connections to ensure safe pool electrical system operation.

Completed MVP cooling maintenance on residential outdoor condensing unit. Performed comprehensive system diagnostics including electrical testing of control board and circuit connections using digital multimeter. Inspected unit exterior condition, filter media, condensate drain lines, and mounting pad. All components operating within normal parameters.

Completed recurring MVP heating maintenance visit. Performed comprehensive system inspection of HVAC equipment including evaporator coil assembly, air filtration system, and refrigerant lines. Conducted combustion analysis testing using calibrated digital analyzer to verify proper natural gas combustion efficiency, oxygen levels, carbon monoxide output, and carbon dioxide concentrations, with readings confirming safe operating parameters at 20.9% O2 and 0 ppm CO. All system components found to be functioning within manufacturer specifications with proper airflow through clean filter media and secure refrigerant line connections.

Performed maintenance service on mini split system by disassembling and cleaning unit. Upon reassembly and testing, discovered blower motor failure requiring replacement. Ordered replacement blower motor assembly and scheduled return visit for installation once part arrived at shop.

Completed routine maintenance on 2-year-old gas furnace. Performed full system inspection including burner assembly, heat exchanger, gas valve connections, control board, and all electrical components. Verified proper operation of all safety controls and cleaned unit as needed.

Conducted comprehensive assessment of 31-year-old residential HVAC system including furnace and air conditioning equipment located in basement utility area. Evaluated existing furnace unit with exposed blower motor assembly, electrical wiring connections, and ductwork configuration including main supply trunk line and return air system. Documented current equipment condition, installation layout, and mechanical room setup to provide detailed replacement estimate for aging system that has exceeded typical service life expectancy.

Completed scheduled MVP heating maintenance visit. Inspected blower assembly and documented condition of squirrel cage fan, noting dust accumulation on fan blades and housing. Photographed small white plastic component, likely a mounting bracket or sensor holder, for maintenance records.

Completed warranty installation of Honeywell Home digital thermostat at residential location. Replacement unit was previously ordered and received at shop prior to service call. Removed defective thermostat, installed new unit on existing wall plate, verified proper wiring connections, and confirmed system operation with accurate temperature display and control functionality.

Completed annual MVP heating maintenance on 1-year-old furnace system. Performed comprehensive inspection of control board and electrical components, verifying all connections, capacitors, and integrated circuits functioning properly. Identified significant corrosion on copper refrigerant line and brass fittings near air handler requiring monitoring for potential future replacement to prevent system failure.

Completed MVP heating maintenance visit on 10-year-old system. Performed diagnostic inspection using thermal imaging camera to assess system components and ductwork integrity. Supply air temperature measured at 72.0°F at the air handler. Identified deteriorated flexible ductwork insulation with visible tears in the outer vapor barrier requiring future attention. System operational and providing heat as designed.

Completed scheduled heating maintenance on basement furnace system with 8am arrival as confirmed. Performed comprehensive inspection of furnace control board and electrical connections, verifying all wire harnesses, terminals, and integrated circuits were properly seated and functioning. Inspected and replaced air filter, which was found to be in serviceable condition. All system components operating within normal parameters with no immediate service needs identified.

Completed annual pre-winter heating maintenance tune-up on a 1-year-old Lennox WT 09-2034 system. Performed comprehensive system diagnostics using digital multimeter to verify proper electrical readings at gas valve and control components, measuring 463 millivolts at the thermocouple connection. Inspected all wiring connections, pressure switches, and gas control mechanisms to ensure safe and efficient operation. System tested and confirmed to be functioning properly with no issues found.

Completed comprehensive furnace maintenance inspection and system evaluation. Removed access panel to examine internal components, including blower assembly, control board, and electrical connections. Inspected green circuit board PCB with all electronic components, DIP switches, and LED display module showing proper configuration and functionality. Verified wire harnesses, connections, and routing throughout unit were secure with appropriate wire management. Noted accumulated dust and debris on blower compartment filter area. Examined drain pan, interior cabinet condition, and all manufacturer safety labels. All electrical components, including integrated circuits, resistors, and control system connections, found to be in proper working order with no signs of damage or wear.

Installed Navien 240 tankless water heater with buffer tank and recirculation system. Ran new dedicated electrical circuit through attic space to power the equipment, including proper conduit and wiring installation per code requirements. Staged and installed complete system with all necessary components including Navien recirculation kit and associated plumbing connections.

Provided quote for replacement of 50-gallon gas water heater with regular vent configuration in tall form factor. Upon inspection, found severe corrosion on top of existing unit, particularly at the copper pipe connections and tank outlet fittings, with visible green copper oxidation and brown rust deposits indicating advanced deterioration. The existing HANDYMAN-branded water heater showed significant age-related wear with corroded brass fittings and compromised piping connections at the tank top. Documented existing installation including galvanized vent piping, copper supply lines, pressure relief valve assembly, and expansion tank configuration for accurate replacement specifications.

Completed full HVAC system installation including outdoor Lennox condensing unit mounted on concrete pad with proper drainage and rock landscaping. Installed refrigerant lines, electrical disconnect, conduit, and all necessary connections to exterior wall with secure mounting brackets. Verified system performance with temperature differential readings showing 162.9°F, confirming proper operation and heat exchange efficiency.

Responded to airflow complaint with excessive air discharge from kitchen and bathroom vents. Investigated multiple HVAC systems on property including 16-year-old Trane furnace in basement, 3-year-old Lennox WT 10-2033 furnace in basement, and 16-year-old Trane AC unit in utility closet to identify source of issue. Inspected ductwork system, including basement-level galvanized steel supply ducts and distribution branches, to diagnose cause of abnormal airflow patterns and determine which system was responsible for the complaint.