Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Responded to a leak at a 1 1/2 x 1 x 1 1/2 copper tee fitting located on the outlet side of the water meter. Rebuilt the configuration from the meter flange, eliminating the problematic 1-inch pipe section, installed a new brass ball valve on the vertical copper pipe run, and securely reconnected all components to the meter flange. The repair successfully resolved the leak and restored proper water flow to the system.

Replaced existing standard VPL outlet with GFCI outlet at outdoor HVAC unit location to provide proper ground fault protection for equipment. Verified all electrical connections were secure, tested GFCI functionality, and confirmed proper operation of the protected circuit.

Replaced defective blower motor and blower wheel assembly in residential furnace unit. Ordered and received necessary replacement parts, then completed installation during a two-hour service call. Unit was tested and verified operational with proper heating and cooling function restored.

Conducted site assessment for outdoor pool lighting installation. Evaluated backyard area and existing electrical infrastructure in basement utility space to determine routing requirements and feasibility for new exterior lighting circuit. Provided comprehensive quote for materials and labor to complete installation.

Responded to service call for non-functioning electrical circuit serving garage. Performed diagnostic assessment of electrical system including inspection of interior switch controls, main panel neutral connections, and garage sub-panel. Traced circuit routing through basement utility area to identify potential points of failure. Documented existing wiring configuration and overhead cable routing for further evaluation and repair recommendations.

Responded to service call for malfunctioning exterior hose bib mounted on building's metal siding. Upon inspection, found existing spigot required replacement due to wear and potential leaking at connection point. Successfully removed old fixture and installed new hose bib assembly with updated valve mechanism and secure mounting to corrugated metal exterior wall. Verified proper water flow, tested for leaks, and confirmed operational functionality of red-handled valve control with turquoise coupling component. Unit now operates correctly and is ready for use.

Responded to service call for non-functioning electrical outlets in section of home. Upon investigation, identified faulty wiring connections at junction box feeding affected circuit. Inspected and tested electrical connections, repaired loose wire terminations, and verified proper grounding. Restored power to all outlets and confirmed proper operation throughout affected area.

Completed MVP cooling maintenance visit on residential HVAC system. Performed comprehensive inspection of outdoor condensing unit, including electrical disconnect switch verification and dual-capacitor system assessment. Documented equipment condition through detailed photography of electrical components, wiring connections, and capacitor configuration. All electrical connections found secure with proper wire routing and color coding intact. System operational and ready for continued service.

Completed full system replacement estimate for 30-year-old heating and cooling equipment. Assessed existing air conditioning unit and furnace for replacement specifications, documented current installation conditions, and photographed equipment locations both interior and exterior. Provided comprehensive replacement options and recommendations for new HVAC system installation.

Responded to service call for non-functional bathroom lighting. Upon inspection, identified wiring issues at the electrical panel and traced circuit to affected bathroom fixtures. Corrected improper connections at the panel, verified proper circuit protection, and restored power to bathroom lighting circuit. Tested all fixtures to confirm proper operation and ensured all connections met current electrical code requirements.

Replaced hot and cold shut-off valves in garage, installed new laundry room faucet, and replaced boiler drains. Work included mounting new copper supply lines with ball valves on backing boards and connecting flexible supply hoses to appliances. Job involved Jack and Jill sink configuration with notation that drywall access in closet behind sinks may be required for drain cable routing if blockage extends between traps.

Performed scheduled maintenance on a 2-year-old Generac residential backup generator. Conducted comprehensive battery load test using digital analyzer, which confirmed battery in good operating condition with acceptable voltage and cranking capacity. Inspected generator unit, electrical connections, and conduit routing along exterior wall, verifying all components functioning properly with no issues identified.

Completed scheduled MVP cooling maintenance visit on residential split system. Performed comprehensive inspection of outdoor condensing unit and indoor air handler, verified proper operation of all components, checked refrigerant lines and electrical connections, and documented system condition with photographs. All equipment found operating within normal parameters with no issues identified requiring immediate attention.

Installed whole home surge protector at main electrical panel. Documented existing conditions including deteriorated cable insulation on service entrance conductors requiring future attention. System tested and operational upon completion.

Responded to no power complaint affecting bedroom ceiling fan and bathroom electrical circuits. Upon investigation, identified tripped circuit breaker at main electrical panel. Reset breaker, restored power to affected areas, and verified proper operation of ceiling fan and bathroom outlets. All circuits functioning normally upon completion.

Responded to clogged bathtub drain on upper level. Accessed plumbing system through existing wall cavity to diagnose blockage. Removed wall access panel to inspect vertical copper water lines and drainage system. Cleared obstruction from bathtub drain assembly, including overflow drain mechanism. Verified proper water flow through tub spout and drain. Restored functionality to bathtub fixture and plumbing components.

Responded to service call for pool heater that was not responding to ignition sequence. Customer requested gas line inspection to eliminate potential gas supply issues as the cause. Performed comprehensive gas line inspection of outdoor installation, examining gas piping connections, valves, and supply lines serving the pool heater equipment. Verified gas line integrity, checked for proper pressure, and confirmed no leaks or obstructions in the gas supply system. Documented equipment configuration including gas meter, piping runs, and connections to pool heating unit with photographic evidence for customer records.

Responded to commercial property for diagnosis of reported water leak and backflow issue. Upon inspection, located plumbing infrastructure with multiple pipe connections including black and copper lines with installed backflow prevention assembly. Identified tagged Apollo backflow device and assessed system configuration, pipe conditions, and connection points to determine source of leak and evaluate backflow preventer functionality for compliance and proper operation.

Completed annual backflow preventer testing and certification for residential irrigation system. Tested the RPZ backflow assembly mounted on exterior wall, confirmed all check valves and relief valve operating within acceptable parameters per local plumbing code requirements. Unit passed inspection and is compliant for continued use.

Responded to service call for reported shower leak. Upon inspection, identified moisture infiltration at shower enclosure corner joint with visible water staining and discoloration along wall-to-floor seam. Examined Delta shower fixture installation and surrounding plumbing connections. Documented deteriorated caulking and seal failure at corner junction where vertical supply line meets the enclosure, allowing water to escape during shower use. Assessed exposed piping for additional leak sources and confirmed primary issue at compromised sealant joint requiring re-caulking and potential trim adjustment to prevent future water damage.