Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Conducted site assessment of existing electrical service in basement utility area. Evaluated two white electrical panel boxes with exposed circuit breakers mounted on plywood backing against concrete block foundation. Inspected condition of panels, breakers, and associated wiring including metallic and PVC conduits running through floor joists. Assessed black disconnect boxes and junction boxes mounted below main panels. Evaluated unfinished basement space with exposed brick walls and determined requirements for establishing proper electrical service to the dwelling. Documented existing infrastructure including overhead piping, ductwork, and cable runs. Identified need for new service entrance conductors and potential panel replacement due to age and configuration of current installation. Photographed existing conditions including panel interiors, conduit routing, and structural elements for quote preparation. Coordinated assessment with plumbing contractor also working on property t

Completed annual air conditioning maintenance on a four-year-old HVAC system. Performed comprehensive tune-up including inspection of furnace interior components, electrical connections, control board operation, blower motor assembly, and air filtration system. Verified proper function of all safety controls, relay operations, and LED indicators on the control board. Customer renewed maintenance agreement at time of service.

Responded to reported gas leak at residential property. Coordinated with gas company for safety notification and conducted thorough inspection of gas line connections and water heater installation. Verified all gas piping, valves, and connections associated with Rheem water heater system for leaks and proper installation compliance.

Completed a 200-amp electrical service upgrade with exterior disconnect installation to meet 2023 National Electrical Code requirements. Installed new meter box assembly with dual meter sockets, circuit breaker panel, and gray PVC conduit routing from the exterior meter location into the ground near the foundation. All necessary code updates were implemented, parts were ordered and delivered, and the installation was mounted on the exterior brick wall with proper conduit connections and grounding.

Responded to a clogged bathtub with drainage backup from the bathroom sink. Upon inspection, found standing water in the tub and confirmed that sink usage was causing wastewater to back up into the bathtub, indicating a blockage in the shared drain line. Accessed the drain system through the crawlspace/ceiling area below the bathroom and inspected the P-trap and waste piping assembly. Cleared the obstruction from the drainage system, restoring proper flow through both the sink and tub drains. Verified that water now drains freely from both fixtures without backup. System is functioning normally.

Performed maintenance inspection on 8-year-old Lennox furnace system with reported blower motor concerns. Accessed and evaluated internal control board wiring, terminal connections, and electrical components within the unit compartment. Documented equipment condition through photography of control board assembly and overall furnace installation, noting complex wiring configuration and system connections including ductwork and PVC venting components.

Responded to service call for 20-year-old air conditioning system failing to reach thermostat setpoint. Performed diagnostic testing using manifold gauges to check refrigerant pressures and system performance. Upon inspection, discovered outdoor condensing unit interior heavily contaminated with dirt, debris, spider webs, and organic material buildup affecting system efficiency. Electrical connections showed signs of age and environmental exposure. System is operational but operating below optimal capacity due to age and lack of preventative maintenance, resulting in insufficient cooling output to satisfy thermostat demand.

Responded to service call for H-S Craftmaster tanked water heater (Model N40S91-403) with non-functioning pilot light and igniter assembly. Upon initial inspection, diagnosed faulty igniter component preventing flame ignition. Ordered replacement parts, which arrived and were staged for second appointment. Returned to property, installed new igniter assembly, tested pilot light operation, and verified proper burner ignition sequence. Confirmed water heater restored to full operational status with adequate hot water production.

Replaced existing tanked water heater with new unit per customer request for expedited installation. Completed full water heater replacement including reconnection of all copper supply and return lines, circulator pump reinstallation, and proper connection of expansion tank. All plumbing connections were secured with appropriate fittings, insulation was applied to hot and cold water lines, and system was tested for proper operation and leak-free performance.

Installed a new 50-gallon Bradford White water heater with 6-year manufacturer warranty in basement utility room. Replaced existing flex lines with copper piping, installed new ball valve on cold water line, and mounted new thermal expansion tank on wall. Upgraded gas line connections by removing old grease valve and appliance whip, installing new gas shut-off valve for improved safety and code compliance. Properly vented unit through existing exhaust system to ceiling, verified all plumbing connections for leaks, and removed old water heater from premises upon completion.

Responded to service call for toilet replacement consultation at residential property. Inspected two upstairs toilets to assess condition and provide replacement recommendations. Both fixtures were in functional working order with no mechanical issues or leaks present. Documented existing toilet configurations, bowl styles, and surrounding floor conditions to facilitate accurate replacement planning and material specifications.

Responded to no power call for fluorescent light fixture previously installed in March. Upon inspection, traced issue to junction box in unfinished area with exposed framing near HVAC equipment. Verified circuit breaker position, tested voltage at junction box, and confirmed proper wire connections. Identified failed ballast in fluorescent fixture as root cause of complete power loss. Replaced defective ballast, restored power to fixture, and verified proper operation before completing service call.

Responded to a toilet backing up in a mobile home. Upon arrival, inspected the toilet and found signs of waste material and staining in the bowl. Removed the tank lid to assess internal components and check for any mechanical issues affecting flush performance. Observed mineral buildup and sediment deposits in the tank, along with water staining on internal components. The fill valve, flush valve, float mechanism, and overflow tube were all examined and found to be functional. Addressed the backup issue through standard clearing procedures to restore proper drainage and flushing operation.

Provided quote for replacement of existing tanked water heater in 80-year-old residential property. Assessed current water heater installation located in basement utility area, noting aged unit with visible corrosion and wear on exterior tank surface. Evaluated existing plumbing configuration including copper supply lines, vent piping, and gas connections. Documented under-sink cabinet plumbing infrastructure and main water heater installation for replacement planning purposes.

Removed basement toilet and performed camera inspection of the sewer line to assess drainage conditions. Video inspection revealed line integrity at 60 feet with no obstructions requiring immediate intervention, confirming proper flow capacity throughout the inspected section.

Responded to kitchen sink clog where ceiling had been previously opened to expose plumbing. Upon inspection, accessed drain assembly in basement/crawl space area and identified blockage in drainage system. Cleared obstruction from kitchen sink drain line, verified proper flow through black plastic pipe assembly and connections, and confirmed system was draining properly with no leaks at fittings or joints.

Responded to service call for corrosion issues at air conditioner disconnect box and exposed cable at electrical mast/service entrance, originally identified during home inspection of 1962-built residence. Upon arrival, conducted thorough visual inspection of exterior electrical components, including weatherhead, service entrance cable, meter base, and AC disconnect enclosure. Documented existing conditions through comprehensive photographic documentation showing the vertical service mast installation on brick exterior, exposed service entrance conductors, meter enclosure, and white rectangular disconnect panel below. Assessed corrosion levels at AC disconnect box and evaluated integrity of exposed cabling at service entrance point where conduit enters the structure. Provided homeowner with detailed findings regarding the condition of electrical service equipment and recommended appropriate corrective measures to address weathering and exposure concerns to ensure continued safe operati

Installed a 40-gallon tall Bradford White water heater with expansion tank in basement utility area. Connected all supply and discharge lines including copper piping, installed 1/2x1/4 shut-off valve, and properly secured expansion tank above unit with copper loop connection. All connections tested and system operational.

Responded to service call regarding inoperative stovetop following recent electrical panel upgrade. Inspected newly installed breaker panel and verified all circuit breakers were properly seated and functioning. Identified that stove circuit breaker required resetting after panel replacement work. Cycled breaker to restore power to stovetop circuit. Confirmed proper labeling of stove circuit and verified electrical connections at panel were secure and torqued to specification. Tested stovetop operation and confirmed full functionality restored.

Replaced deteriorated bathtub waste and overflow assembly with new lift-and-turn style unit due to failed gaskets causing intermittent leaking from overflow. Removed existing union-style trap beneath tub and installed permanent glued PVC trap with new trap adapter to eliminate potential leak points and ensure proper drainage. Parts were coordinated through shop for timely completion of repair work.