Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Responded to water leak in basement utility area. Upon inspection, identified leaking PVC pipe running vertically along concrete block wall. Repaired pipe connection, secured mounting brackets, and verified all plumbing connections were properly sealed. Tested system for leaks and confirmed repair was successful with no further water discharge detected.

Completed comprehensive MVP heating maintenance inspection and documentation of evaporator coil assembly. Performed visual assessment of heat exchanger fins, which showed clean condition with proper spacing and no visible debris accumulation, and verified structural integrity of housing components and mounting hardware.

Completed scheduled MVP heating system maintenance visit. Performed diagnostic testing of electrical components using digital multimeter, verifying proper voltage readings at control board connections and motor assemblies. Inspected control board wiring, relays, contactors, and all terminal connections for secure attachment and proper operation. All system components found operating within normal parameters and heating unit confirmed functioning correctly.

# Furnace Tune-Up Completed Performed comprehensive preventive maintenance on a 3-year-old gas furnace. Conducted electrical diagnostics using digital multimeter to verify proper voltage and resistance readings across control board components, measuring 45 ohms on critical circuit paths. Inspected and tested all electrical connections, including control board relays, capacitors, and terminal blocks. Verified proper operation of all safety controls and confirmed secure wire routing throughout the equipment cabinet. All systems tested and operating within manufacturer specifications.

Completed repair of leaking outdoor hose bib that was spraying water at the exterior wall penetration. Accessed interior crawl space to replace failed valve assembly and secure copper supply line. Tested system under full pressure to confirm leak elimination and proper operation of the outdoor spigot.

Performed routine maintenance flush on residential tanked water heater installed in 2022. Drained sediment buildup from tank bottom through drain valve, flushed system with fresh water until discharge ran clear, and refilled tank completely. Verified all plumbing connections, expansion tank, and pressure relief valve for proper operation. Inspected copper piping, PEX connections, and circulation pump for leaks or signs of wear. System restored to normal operation with no issues identified.

Performed main drain snaking service to clear plumbing system and prevent future backups. Successfully accessed the main cleanout fitting located in the basement utility area, snaked the drain line to remove blockages and restore proper flow, and confirmed system is operating correctly to prevent recurrence of previous backup issues.

Completed MVP Cooling Maintenance on residential HVAC system. Performed comprehensive inspection of outdoor disconnect box, verifying proper fuse operation and electrical connections, and inspected indoor furnace unit including ductwork connections and system components. All equipment found operating within normal parameters with no deficiencies noted.

Performed comprehensive tune-up and cleaning on eleven-year-old furnace with no reported operational issues. Completed standard maintenance procedures including inspection of flame sensor and electrical connections, all components found in proper working condition. System operating efficiently with no deficiencies noted.

Completed MVP heating maintenance visit on 6-year-old furnace system. Performed comprehensive inspection of heating equipment and replaced dirty air filter with new filter to ensure proper airflow and system efficiency. Conducted simultaneous air conditioning system inspection on outdoor condensing unit, including examination of electrical connections, capacitor, control board, and refrigerant lines. Verified all wiring connections were secure and capacitor was functioning within specifications. Checked condensate drainage system and PVC piping for proper operation. Customer renewed membership during visit to continue coverage for future preventative maintenance services.

Completed annual precision tune-up on one-year-old furnace and air conditioning system. Performed comprehensive inspection of outdoor condensing unit, verified electrical connections and amperage readings using clamp meter, inspected and tested FLNR 50 amp fuses in disconnect box, checked refrigerant pressures, cleaned condenser coil, and evaluated overall system performance. All components found operating within manufacturer specifications with no issues identified during routine maintenance visit.

Completed scheduled BS-MVP preventative maintenance visit on 3-year-old furnace system. Performed comprehensive inspection of heating equipment including examination of flame sensor assembly, which was removed and photographed showing normal electrode condition with minor surface oxidation. Thoroughly inspected furnace control board and electrical components, verifying all wire connections, relays, and capacitors were secure and functioning properly. All system components operating within normal parameters with no deficiencies noted at time of service.

Completed MVP furnace maintenance including full system inspection and diagnostics. Verified control voltage readings at 49.9V and checked all low-voltage control wiring connections for proper operation. Inspected furnace components and confirmed system is operating within normal parameters.

Performed maintenance and efficiency testing on 4-year-old MVP heating furnace system. Combustion analysis confirmed optimal performance with oxygen level at 6.6%, carbon monoxide at 27 ppm, efficiency at 99.1%, and carbon dioxide at 8.0%. Inspected blower wheel assembly and verified clean operation with no debris accumulation on blades or housing.

Completed comprehensive furnace tune-up including combustion analysis and air filtration system inspection. Verified proper operation with combustion analyzer readings showing stack temperature of 108°F, air temperature of 211°F, and monitored CO/CO2 levels to ensure safe and efficient operation. Inspected and evaluated pleated air filter condition within the air handling system to maintain optimal airflow and indoor air quality.

Completed preventive maintenance inspection on residential air conditioning system for MVP customer. Performed electrical diagnostics using digital multimeter, recording voltage readings of 33.52V and 46.4V at the outdoor condensing unit. Inspected condenser coils, which were found to be clean and in good condition. Examined outdoor disconnect box and contactor assembly, noting operational components with minor age-related weathering present in enclosure. System operating within normal parameters; documented findings with photos for customer records.

Completed MVP recurring heating maintenance visit. Performed system diagnostics using digital combustion analyzer, recording gas pressure readings and combustion efficiency parameters. Inspected evaporator coil assembly, confirming clean fins and proper airflow through curved coil section with no visible blockages or debris accumulation.

Completed scheduled MVP heating maintenance on a 5-year-old gas-powered furnace system. Performed comprehensive inspection of heat exchanger assembly, U-bend tubes, and finned coil sections, noting accumulated dust and operational residue consistent with normal system usage. Documented equipment condition through photographic records showing internal components including refrigerant lines and heat exchanger configuration, confirming system eligibility for service renewal under recurring maintenance program.

Responded to emergency carbon monoxide leak from tanked water heater. Upon arrival, property was evacuated and emergency services had been contacted. Inspected Bradford White water heater unit and surrounding ventilation system. Found significant dust and lint accumulation on HVAC blower housing and ductwork, which may have contributed to improper ventilation. Examined metallic vent pipe configuration and copper supply lines for proper installation and clearances. Documented equipment condition, including water heater specifications, expansion tank installation, and deteriorated basement wall conditions that showed moisture damage. Photographed all relevant equipment and safety concerns for record and follow-up assessment.

Replaced eight end-of-life smoke detectors throughout residential property with new 10-year sealed battery units. Installed combination smoke/carbon monoxide detectors on each floor level and individual smoke detectors in all bedroom locations. Blanked off one redundant detector location on the second floor where two units were positioned adjacent to each other.