Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Completed MVP recurring maintenance visit on heating system. Performed comprehensive inspection of furnace unit, documenting blower motor assembly, electrical connections, and capacitor specifications (5.1a/5uF noted). All wiring connections secure with proper wire nuts, manufacturer labels and safety warnings verified intact and legible, unit operational and functioning within normal parameters.

Completed scheduled MVP maintenance visit on heating system over 10 years old. Inspected and removed flame sensor, which showed significant carbon buildup and deterioration on the sensing rod and ceramic insulator. Cleaned blower wheel assembly, which had accumulated substantial dust and debris on the squirrel cage blades affecting airflow efficiency. Verified all electrical connections and wiring harnesses were secure and properly seated. System tested and returned to normal operation.

# HVAC Install - Complete System Completed installation of a 90% efficiency furnace system with integrated HVAC components in mechanical room. Installed new beige cabinet furnace unit as primary heating source, positioned centrally in equipment lineup. Mounted metallic air handler with connecting ductwork for proper air distribution throughout structure. Configured white PVC venting system extending from furnace top for combustion air intake and exhaust requirements per manufacturer specifications. Installed water heater unit with appropriate safety labeling and warning placards clearly visible on front panel. Established all necessary gas line connections using black pipe with blue-handled shutoff valve for system isolation capability. Installed brass fittings at connection points to ensure secure, leak-free operation. Routed plumbing connections between units for integrated system performance. Completed ductwork installation including foam-insulated supply ducts and metallic flexi

Replaced deteriorated cast iron drain piping for double lavatory system by opening walls on both sides of the drain assembly. Cut and removed existing cast iron pipe above the vent down past the long sweep 90-degree fitting. Installed new PVC drainage piping from the cut point downward, transitioning from PVC to existing cast iron using code-approved no-hub transition bands. Installed new P-trap assemblies at both sink locations to complete the drainage system upgrade.

Responded to water leak complaint in utility area with pooling around HVAC system and water heater. Upon inspection, identified active water staining and mineral deposits on concrete floor beneath both units. Traced source to condensate drain line from HVAC air handler, which was clogged and causing overflow. Cleared condensate line blockage, verified proper drainage, and tested system operation. Inspected water heater for leaks and found no plumbing issues. Educated occupant on condensate system maintenance and recommended monitoring area for recurrence.

Completed MVP heating maintenance inspection and system evaluation. Performed standard preventive maintenance procedures, verified proper operation of heating equipment, and documented system condition with photographic records. All components found to be functioning within normal parameters.

Replaced internal components within the VESTA water softener control head to resolve continuous water discharge issue. Installed new valve assembly parts and control mechanisms to restore proper regeneration cycle function and prevent system from bypassing or continuously draining.

Replaced defective T-fitting and installed new coupling on PEX water supply line in exposed wall cavity. Utilized PEX crimping tools to secure connections on both hot and cold water lines, ensuring proper flow and eliminating existing leak point.

Accessed the second floor hall bathroom through ceiling opening to address toilet flange failure. Removed existing damaged flange and installed new replacement flange to restore proper toilet mounting and seal integrity. Completed repair in 5 hours, resolving drainage concerns and ensuring secure fixture installation.

Completed installation of a 10 kW backup generator system with a 100-amp whole home transfer switch. Ran 30 feet of gas line and 30 feet of electrical conduit to connect the unit to the home's existing systems. Coordinated required disconnect with AEP utility company to ensure proper integration with the electrical grid.

Completed electrical rewiring in basement utility area to accommodate new dishwasher installation. Ran new dedicated circuit with appropriate gauge wiring through exposed joist space, installed junction box, and verified all connections met code requirements for appliance load.

Completed dryer vent cleaning service for a residential property. Upon inspection, found significant lint and debris accumulation throughout the duct system, with multiple layers of fibrous material coating the interior walls and restricting airflow. Thoroughly cleaned the entire vent line from the dryer connection to the exterior termination point, removing all accumulated lint, dust, and debris to restore proper ventilation and reduce fire hazard risk.

Performed preventive maintenance descaling service on Rinnai tankless water heater unit. Flushed system with descaling solution to remove mineral buildup and ensure optimal heat exchanger performance and efficiency. Unit tested and verified operational at 135°F upon completion.

Conducted on-site evaluation of existing 40-gallon natural gas water heater located in basement utility area. Inspected unit manufactured in 2013 and documented current installation conditions including proximity to wooden shelving structure and concrete block foundation walls. Assessed plumbing connections, venting requirements, and clearance specifications for potential replacement. Photographed equipment specifications, safety labels, and surrounding work area to prepare comprehensive replacement estimate. Customer available for consultation during standard business hours with advance notification requested.

Responded to service call for slow draining kitchen sink and three bathroom drains experiencing backup issues. Upon arrival, performed diagnostic assessment of all affected fixtures. Kitchen sink showed signs of drainage obstruction with double-basin stainless steel configuration requiring attention. Bathroom sink displayed evidence of severe backup conditions with extensive staining throughout basin and countertop surfaces indicating prolonged drainage problems. Cleared blockages from main drain lines servicing kitchen and bathroom fixtures using appropriate drain cleaning equipment. Restored proper water flow and drainage function to all affected sinks. Verified successful clearance by testing each fixture for adequate drainage speed and confirming no remaining backup conditions. All drains now operating within normal parameters.

Responded to clogged bathtub drain at duplex property. Coordinated with landlord to ensure both tenants were present for inspection. Upon arrival, contacted customer with preliminary findings as requested. Performed thorough assessment of drainage system, including inspection of accessible plumbing infrastructure beneath the unit. Documented existing conditions showing aged piping with visible corrosion on metal components and PVC drain lines in crawl space. Addressed the bathtub blockage and verified proper drainage function upon completion.

Completed scheduled tune-up service on 3-year-old Carrier furnace and humidifier system located in basement. Replaced air filter and humidifier filter as requested, performed visual inspection of all system components including ductwork, venting, and electrical connections. System operating within normal parameters with no issues identified during service visit.

Completed annual furnace maintenance inspection on 5-year-old system with no reported issues. Performed comprehensive tune-up including filter inspection, electrical system diagnostics measuring 5.18 amp draw, and visual inspection of all accessible components. System operating within normal parameters; confirmed annual maintenance schedule is recommended for optimal performance and warranty compliance.

Completed MVP cooling and heating maintenance service at residential property. Performed comprehensive system inspection with electrical diagnostics using multimeter to verify proper voltage and amperage readings across components. Accessed outdoor condensing unit electrical compartment, inspected capacitor, contactor, relay, and control board connections. All electrical components tested within normal operating parameters, wiring connections secure, and system operating efficiently with no deficiencies noted.

Delivered salt for water softener system and inspected brine tank for reported bridging issue. Confirmed salt bridge formation in tank, broke up hardened salt layer to restore proper water contact and ensure system functionality. Restocked salt supply and verified water softener operation upon completion.