HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Completed installation of new kitchen faucet with brushed nickel finish and replaced both hot and cold water shutoff valves under the sink. The service required a second appointment to complete all work, with new compression fittings and flexible supply lines properly connected to ensure leak-free operation.

Completed MVP recurring cooling maintenance visit on Bryant outdoor condensing unit. Performed comprehensive system inspection including examination of electrical components, capacitor condition, and wiring connections. Unit operating within normal parameters with all components functioning properly at time of service.

Completed comprehensive furnace tune-up and system inspection on MVP unit. Performed diagnostic testing of blower motor assembly, verified all electrical connections and wire terminations were secure, and conducted temperature measurements at control board to ensure proper system operation. All components found functioning within normal parameters.

Conducted on-site assessment for whole house central air conditioning system replacement. Evaluated existing Carrier air handler unit in basement showing evidence of chronic condensate drainage issues with significant water staining on adjacent wall surfaces. Inspected electrical service panels and circuit capacity to determine compatibility with new system installation. Provided estimate for complete AC system replacement with recommended installation timeline for spring 2027 to optimize cost-effectiveness and availability.

Responded to no heat call on recently installed thermostat. Upon inspection, performed diagnostic camera inspection of internal components and identified issues with electrical connections and oxidized copper tubing within the unit. Documented existing wiring configuration including relay connections and assessed condition of mechanical components to determine cause of heating system failure.

Responded to service call for a two-year-old natural gas water heater with water accumulation in the drain pan. Upon inspection, discovered significant corrosion and oxidation at the hot water outlet connection, with brownish-orange rust deposits accumulated at the copper pipe fitting junction. The corrosion at the brass compression fitting indicated a slow leak that had been depositing water into the safety pan. Documented the condition of the water heater installation, including the expansion tank connections and overall system configuration. The compromised fitting at the hot water outlet required attention to prevent continued water discharge into the drain pan and potential water damage.

Completed MVP AC maintenance on outdoor condensing unit. Removed access panel to expose heavily clogged condenser coil with significant accumulation of dirt, dust, and debris causing restricted airflow. Cleaned condenser coil, removed buildup from exterior surfaces, and restored unit to proper operating condition. Unit tested and operating within normal parameters upon completion.

Removed and replaced an old Mansfield toilet that was leaking at the base with a new American Standard Cadet elongated bowl, right height model with slow-close seat. Replaced a corroded straight stop shut-off valve with a new chrome shut-off valve to ensure proper water supply control and prevent future leaks.

Responded to service call for loose kitchen faucet handle. Upon inspection, determined existing faucet required replacement due to worn internal components and mounting issues. Installed new brushed nickel finish kitchen faucet per customer request, ensuring proper connection to existing water supply lines. Verified hot and cold water lines, tightened all mounting hardware, and tested for leaks. Confirmed proper water flow and handle operation upon completion.

Conducted furnace replacement estimate for residential property. Evaluated existing Trane furnace installation in basement utility room, documented current system configuration including ductwork connections, PVC condensate drainage system, and adjacent air handler components. Photographed equipment specifications, installation layout, and mechanical room conditions to provide comprehensive assessment for replacement proposal.

Conducted free estimate for relocating existing white cast iron radiator in kitchen area to accommodate remodeling plans in older residential home. Assessed current radiator positioning, existing piping configuration, and structural considerations for proposed relocation within the space.

Installed customer-supplied ceiling fan with integrated light fixture in bedroom, including electrical connections at ceiling junction box, mounting hardware installation, and blade assembly. Verified proper operation of fan motor and lighting element, confirmed secure mounting and electrical safety compliance.

Completed comprehensive MVP heating maintenance service on residential HVAC system. Performed diagnostic testing using digital manifold gauge to measure system pressures and temperatures, recording readings for refrigerant levels and operational parameters. Conducted thorough inspection of internal components including blower assembly, heat exchanger, and associated mechanical equipment, verifying proper operation and identifying areas showing normal wear patterns.

Completed furnace installation with air scrubber integration, reusing existing filter components and removing humidifier from system. Installed new ductwork connections in attic space with proper insulation and mounted safety detector, ensuring all components meet code requirements and system operates efficiently.

Responded to failed mechanical final inspection for HVAC installation. AC condenser was missing required locking cap per RCO 1411.8 code compliance. Installed missing locking cap on refrigerant line connection and documented completion with photos showing properly secured line set connections and condenser unit.

Replaced defective GFCI outlet that was producing clicking noises in tiled wall area. Customer-supplied replacement outlet was installed and tested for proper ground fault protection. Verified circuit breaker connection at main electrical panel and confirmed all safety functions operational upon completion.

Responded to service call for multiple water leaks in kitchen area. Repaired leaking supply line under kitchen sink and replaced damaged water line connection to refrigerator. Additionally, performed comprehensive inspection of gas fireplace components, checking all connections for leaks and verifying operational functionality of the unit.

Completed maintenance on gas furnace over 10 years old, performing comprehensive inspection and cleaning procedures. Utilized inspection camera to examine heat exchanger and internal components for cracks, corrosion, or structural integrity issues, documenting findings with digital imagery. All critical systems checked and unit left in proper working order.

Completed MVP air conditioning maintenance service, which included inspection and filter replacement. Removed and examined the existing air filter, which showed significant dust and particulate accumulation requiring replacement. Verified electrical connections and wiring at the equipment panel, ensuring all components were properly secured and functioning within normal parameters.

Completed comprehensive heating maintenance on a 6-year-old furnace system. Performed diagnostic testing of gas valve assembly and electrical components using digital multimeter, confirming proper voltage readings at 48.8V. Inspected heat exchanger coils, burner assembly, and all wiring connections; verified system operation and safety controls functioning within manufacturer specifications.