HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Successfully installed a new 93% efficient furnace in the basement utility room. The installation included proper connection of white PVC venting pipes and copper lines, with all components securely mounted against the concrete block wall. Visual inspection confirms clean installation with appropriate clearances and proper integration with existing mechanical systems.

Diagnosed 25-year-old furnace with temperature regulation issues causing inconsistent heating cycles where temperature would drop into 60s before reactivation despite 70°F setpoint. Performed visual inspection of blower motor assembly and gas valve components, documenting condition with photos for assessment of system functionality.

Diagnosed non-functioning heating system with significant corrosion and rust on heat exchanger. Inspection revealed deterioration of metal components and potential safety hazards. Recommended system replacement due to age-related wear and compromised operational integrity.

Successfully completed toilet replacement service, including installation of a new white porcelain toilet and replacement of the existing shut-off valve. Properly mounted the new toilet to the floor flange and verified proper operation after installation.

Inspected corner tub with non-functioning hot water knob. Evaluated existing bathroom fixtures and provided customer with estimate for toilet and sink replacement options as requested.

Performed scheduled furnace maintenance on MVP system for winter-absent homeowner. Inspected electrical control panel components and connections, confirming proper operation of control module and circuit board. Examined air filter, which showed minimal soiling and proper installation, ensuring optimal system performance for continued heating operation.

Successfully replaced defective flame sensor in Hershel unit to restore proper heating function. Verified secure mounting of sensor assembly and confirmed normal operation of all electrical components after repair.

Responded to no-heat call for residential furnace. Upon inspection, accessed interior components with hex key and found system unresponsive. Diagnosed faulty ignition sequence, cleaned flame sensor and verified proper gas valve operation. System now functioning correctly with normal heating cycle restored.

Conducted free assessment of existing Richmond tanked water heater for potential replacement. Examined current installation including supply/return lines, ventilation ducting, and valve connections. Inspected floor drain and wall-mounted plumbing configuration to evaluate replacement options and requirements.

Performed scheduled furnace maintenance for maintenance program customer. Inspected electrical components including circuit board and wiring connections. Examined and verified proper operation of ignition system components including igniter/flame sensor.

Responded to no-heat complaint for furnace showing intermittent operation. Upon inspection, identified loose electrical connections at the blower motor and control board. Cleaned dust accumulation from internal components, secured all wiring connections, and verified proper electrical continuity. System now functioning properly with consistent operation.

Performed scheduled furnace preventative maintenance. Inspected heat exchanger and air handling components, noting dust accumulation on evaporator coil. Observed minor water damage/corrosion at unit base requiring future monitoring. System operational with MVP service completed.

Replaced faulty receptacle for garbage disposal with new electrical outlet. Inspected breaker panel to verify proper circuit connections and ensure safe operation of the newly installed outlet.

Completed replacement of defective inducer motor and pressure switch on customer's HVAC system. Obtained necessary parts from supply house, installed components according to manufacturer specifications, and verified proper system operation. All wiring connections were properly secured, and system was tested to confirm restoration of normal heating function.

Responded to customer call regarding gas line access needs. Upon inspection, accessed plumbing infrastructure through ceiling and wall cavities to examine cast iron piping and gas line components. Inspected connections, elbow joints, and overall system integrity. No parts required for this service call.

Responded to no heat complaint on 9-year-old furnace where thermostat was reading 66°F despite 72°F setpoint. Diagnosed system malfunction, performed necessary repairs using Fieldpiece diagnostic tools and DeWALT equipment to restore proper heating functionality. System now operating within specifications.

Successfully installed an AprilAire 600 humidifier system on the existing HVAC unit in an unfinished basement area. Mounted the humidifier housing to the ductwork, connected water supply lines with appropriate valves, and ensured proper integration with the existing ventilation system. All connections were secured and system functionality was verified upon completion.

Performed scheduled MVP furnace maintenance service. Inspected residential HVAC system including furnace and associated ductwork. Examined air filter which showed normal accumulation of dust and debris; filter condition indicates regular replacement schedule should be maintained for optimal system performance.

Performed scheduled MVP heating maintenance service. Inspected internal electrical components and connections of furnace system, including circuit board, wiring harnesses, and gas valve assembly. All components functioning properly with no issues detected.

Performed comprehensive furnace tune-up including thorough inspection of control board circuitry and motor assembly. System components were found in good working condition with proper wire connections. Inspected ductwork for disconnections; all systems operating within normal parameters.