HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Completed installation of Performance 80% efficiency furnace as secondary heating unit in customer's basement. Connected unit to existing ductwork and verified proper venting. All connections were secured and system was tested for proper operation before completion.

Diagnosed kitchen sink drainage system with reported leaking issues. Inspected dual-basin setup with metal sink basins connected to a gray PVC drain pipe and white P-trap. Identified mineral deposits at connection points and possible water damage on cabinet surface, indicating long-term seepage. Resolved leaking by tightening connections and ensuring proper alignment of drainage assembly.

Diagnosed and repaired toilet with sewer gas odor and gurgling sounds during flush. Identified partially blocked vent stack causing negative pressure in drain line, cleared obstruction, and confirmed proper venting. Toilet now flushes quietly with no odor issues.

Diagnosed and serviced Rinnai tankless water heater displaying error code 10. Inspection revealed significant rust accumulation on internal components, particularly around the heat exchanger and valve assembly. Cleaned scale buildup, inspected wiring connections, and performed system reset to restore normal operation.

Performed routine MVP heating maintenance visit. Conducted system diagnostics with UEi EM201B gauge, obtaining pressure reading of +3584. Inspected furnace filter which showed significant dust accumulation, indicating replacement is needed soon.

Performed scheduled maintenance on MVP furnace. Inspected blower assembly which showed normal dust accumulation on fan blades. Removed and replaced heavily soiled air filter with significant particulate buildup, restoring proper system airflow.

Performed routine furnace maintenance for MVP customer. Inspected HVAC system including ducting, PVC condensate lines, and connections - all in good condition. Identified and replaced severely dirty air filter with significant dust accumulation in diamond mesh pattern, which was restricting airflow.

Performed annual furnace maintenance service for MVP member (rolled appointment from 11/21). Conducted thorough inspection of furnace control board, wiring connections, and electrical components. All systems functioning properly with no issues detected. Unit left in good working condition.

Conducted comprehensive inspection of existing HVAC system in unfinished basement. Assessed ductwork configuration, noting multiple branches with connecting joints and elbows, and evaluated space for potential installation of furnace replacement with high-efficiency unit. Discussed customer's interest in additional air purification options and humidifier integration with the new system.

Performed routine preventative maintenance on Lennox furnace system. Inspected the unit including exhaust/intake PVC pipes and examined the air filter which showed normal dust accumulation. All systems functioning properly after MVP service completed.

Performed scheduled maintenance on customer's furnace per MVP agreement. Inspected filter and found significant dust accumulation and potential mold growth requiring replacement. Examined internal components including gas valve assembly, circuit board, and wiring connections - all functioning properly with no visible damage or anomalies.

Performed scheduled maintenance on Lennox mini split system. Inspected interior components including control board, wire connections, and blower motor assembly. Verified all electrical connections were secure and properly functioning with no signs of damage or deterioration.

Conducted inspection of 22-year-old furnace with confirmed crack in heat exchanger. Assessment revealed system requires full replacement based on age and safety concerns. Documented condition of existing HVAC system including Rheem water heater and associated ductwork in basement utility area. Customer was left a message to confirm dispatch coordination for replacement.

Performed scheduled MVP heating maintenance service that was previously rescheduled. Inspected control board circuitry and connections, documenting condition with photos. Utilized specialized tool for necessary adjustments to ensure proper system operation.

Completed scheduled maintenance on two Carrier furnace units. Inspected circuit board components and connections, confirming proper operation of control systems. Examined and secured ignitor assembly components to ensure reliable heating performance.

Performed scheduled maintenance on Carrier furnace system with attached Space-Gard humidifier. Completed full inspection of internal components including wiring connections, motor function, and control mechanisms. Used hex key tool to access and service necessary components, ensuring proper operation for the heating season.

Performed standard furnace tune-up on 12-year-old unit. Conducted visual inspection of heat exchanger using camera scope which revealed normal wear consistent with age. System operation verified and confirmed proper functionality with no immediate concerns identified.

Performed scheduled heating maintenance visit on customer's HVAC system. Inspected internal components including circuit board, blower assembly, and gas valve. Examined blower wheel and fan assembly for proper operation and cleaned components to ensure optimal system performance.

Identified and repaired water softener leak occurring during backwash cycle by replacing worn valve seals in the main control assembly. Serviced the E-valve mechanism and renewed customer's service plan as requested, ensuring proper operation of the water treatment system.

Performed scheduled heating maintenance visit. Discovered heavily clogged air filter with significant dust and debris accumulation. Inspected blower motor assembly and electrical connections, noting proper wire routing and component condition.