HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Completed installation of 80% efficiency furnace and air conditioning system. Installed new outdoor condensing unit on equipment pad with proper refrigerant line connections to the residence, and upgraded electrical disconnect with new CLASS RR FLNR 20A fuses rated for 250 VAC to ensure safe operation of the new HVAC equipment.

Completed full HVAC system installation including new air handler unit with supply ductwork and outdoor condensing unit. Installed 20-amp dual fuse disconnect at exterior unit, ran condensate drain line from air handler using PVC piping, and completed all electrical connections between indoor and outdoor equipment. System tested and verified operational upon completion.

Completed comprehensive MVP furnace maintenance inspection and system evaluation. Performed thorough examination of all major heating components including blower motor assembly, heat exchanger, control board wiring, and internal mechanical systems. Verified proper operation of air distribution system through supply diffusers, confirmed clean condition of venting components, and documented system status with detailed photographic records for service history.

Completed MVP recurring cooling maintenance visit on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including removal of top panel to access internal components, inspection of fan motor and blade assembly, and verification of electrical connections. Cleaned condenser coil fins, checked refrigerant line insulation integrity, and confirmed proper unit operation upon completion.

Completed MVP cooling maintenance visit on residential outdoor condensing unit. Inspected condenser coil fins which showed normal weathering and some dirt accumulation, verified proper clearance from surrounding vegetation and confirmed unit was level on concrete pad. Examined and documented electrical components including 30-amp TR30R time-delay fuses rated at 250V AC, which were found in serviceable condition. Inspected condenser fan motor and housing for proper operation and structural integrity.

Completed comprehensive MVP air conditioning maintenance on residential outdoor condenser unit. Performed thorough inspection of cabinet, fan assembly, and protective grille, confirming proper operation of axial fan motor and secure mounting of all components. Verified unit positioning on concrete pad with adequate clearance from surrounding vegetation and landscaping. Inspected electrical conduit, refrigerant lines, and PVC condensate drainage system for proper installation and functionality. Cleaned exterior surfaces, removing accumulated dirt, debris, and organic matter from cabinet panels and gravel base area. Confirmed adequate airflow through louvered side panels and verified all safety guards and protective components are secure and in good working condition.

Completed MVP recurring cooling maintenance visit on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified proper operation of all components, checked refrigerant line insulation integrity, and confirmed unit is operating within manufacturer specifications. System found to be in good working condition with no immediate service needs identified.

Responded to service call for main house fuse repeatedly blowing while operating a one-year-old air conditioning system. Performed electrical diagnostics using multimeter at the outdoor condenser unit, measuring voltage and amperage to identify potential overcurrent condition. Inspected capacitor as suggested by customer's electrician, along with compressor and fan motor electrical components, to determine root cause of circuit overload and eliminate newly installed equipment as source of repeated power failures.

Disconnected flexible gas hose from dryer connection point and shut off gas supply valve to the appliance line. Removed the disconnected gas hose from the area and verified proper valve closure to ensure safe isolation of the gas line, leaving the capped supply line secured in the utility room.

Completed scheduled MVP cooling maintenance visit on residential air conditioning system. Inspected outdoor condenser unit and interior ductwork components, including louvered grilles and sheet metal connections. All components found in operational condition with minor surface debris accumulation noted on condenser fins and duct grilles.

Completed annual maintenance on 11-year-old residential air conditioning system. Performed comprehensive inspection of Lennox HVAC equipment including furnace and air handler units located in basement mechanical room. Accessed and inspected control board assembly, verifying proper operation of electronic components, circuit boards, and electrical connections. Examined wiring harness integrity, terminal connections, and safety controls within equipment cabinet. Checked all manufacturer labels and specifications for compliance. Inspected condensate drainage system including PVC piping and verified proper routing and flow. System operational and ready for cooling season.

Completed scheduled MVP cooling maintenance visit on Goodman furnace system. Performed comprehensive inspection of unit, verified proper operation of all components, checked refrigerant lines and PVC venting connections for secure installation and proper function. System operating within normal parameters with no issues identified during inspection.

Completed preventative maintenance on Lennox outdoor condensing unit. Performed comprehensive inspection of control board including DIP switch configuration verification and outdoor discharge air sensor connections. All electrical components, capacitors, and circuit board connections found in proper working condition. Unit exterior cleaned, fan operation verified, and system confirmed operational with no deficiencies noted.

Completed comprehensive MVP furnace maintenance including full system inspection and control board examination. Removed and inspected integrated furnace control (IFC) board, verifying all electronic components, circuit connections, and LED diagnostics were functioning properly with no signs of damage, corrosion, or component failure. Reinstalled control board, confirmed proper wiring connections to all system components including blower motor, gas valve, and safety circuits, and verified unit operation through complete heating cycle.

Responded to a hall bathroom toilet leaking at the base with water infiltrating into the basement below. Upon inspection from the basement, identified a broken original cast iron closet flange with a failed repair flange previously installed on top of the damaged original. Removed the existing toilet and assessed the full extent of the drainage system failure. Cut out the deteriorated cast iron riser pipe and installed a new transition coupling to convert from cast iron to PVC. Ran new PVC pipe and installed a new closet flange, ensuring proper elevation and secure mounting to the subfloor. Replaced the toilet with a new American Standard Cadet Pro round bowl, right height model, equipped with a slow-close seat. Tested the installation for proper operation and verified no leaks at the base or in the basement. Supply line reconnected and system returned to full service.

Completed comprehensive duct cleaning service in attic space, removing accumulated dust, debris, and particulate matter from HVAC ductwork and surrounding structural areas. Before-service photos documented heavy dust accumulation on wooden joists, beams, and horizontal surfaces, along with visible debris on attic flooring near ductwork components. Successfully cleaned all accessible duct sections and improved overall indoor air quality by eliminating contaminants from the ventilation system.

Responded to no cooling complaint on 7-year-old AC system that remained non-functional following previous service visit. Performed comprehensive system evaluation using inspection camera to assess internal components and ductwork connections. Documented refrigerant line routing and plenum configuration, identifying potential issues with system operation that required further diagnostic attention beyond initial assessment.

Completed MVP air conditioning maintenance on outdoor condenser unit. Performed comprehensive system inspection, cleaned accumulated debris and leaves from unit exterior and surrounding area, checked refrigerant levels and electrical connections, and verified proper operation of all components. Unit showed signs of age with surface weathering but demonstrated satisfactory performance upon testing.

Responded to no water/zero pressure complaint at residential property on well system. Upon arrival, inspected well pump system and electrical components in mechanical room. Found faulty pressure switch and relay assembly preventing pump operation. Tested electrical connections at junction box and verified power supply to pump motor. Replaced defective pressure switch and cleaned corroded terminals on relay contactor. Inspected green circulation pump for proper operation and verified all gate valves were in open position. Checked pressure gauge readings and confirmed system was building adequate pressure. Cycled pump multiple times to ensure proper cut-in/cut-out function of new pressure switch. Restored full water pressure throughout residence and verified flow at multiple fixtures. System operating normally at time of departure.

Responded to main bathroom for clogged toilet with suspected wax ring leak. Upon inspection, found toilet bowl heavily soiled with significant staining and accumulation in drain opening. Assessed underlying plumbing infrastructure in crawl space, noting severely corroded cast iron waste pipe with extensive rust and mineral deposit buildup on drainage system. Cleared toilet obstruction and evaluated wax ring seal at base where discoloration indicated potential leak point. Documented existing conditions of deteriorated waste line and recommended monitoring for future replacement due to advanced pipe corrosion that could contribute to ongoing drainage issues.