HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Responded to a laundry room wash sink drain backup causing water to leak onto the floor. Upon inspection, found the drain line beneath the sink was clogged with accumulated debris. Cleared the obstruction using a drain auger, restored proper drainage flow, and tested the system to ensure no further backup or leakage. Verified all P-trap connections were secure and functioning correctly.

Installed new bathroom vanity countertop with integrated sink and modern single-handle faucet. Addressed slow drainage issues in both bathroom sink and bathtub drains to restore proper water flow.

Performed follow-up inspection on recently installed mini split system to address outstanding installation issues. Documented missing cover components, unlevel unit positioning, and improper routing of refrigerant lines and condensate drain requiring cleanup and securing. Identified concerns with protective cover installation over condenser coil fins that may impact airflow and serviceability, recommending corrective measures to ensure optimal system performance and compliance with manufacturer specifications.

Responded to a shower leak causing water damage to the kitchen ceiling below. Upon arrival, accessed the plumbing system through the wall to locate the source of the leak. Investigation revealed corroded plumbing components with significant rust staining on vertical supply lines behind the shower/tub enclosure. Cut an access opening in the wall to expose the affected pipes and framing. Identified the failed connection causing water to penetrate through the floor assembly into the ceiling cavity below. Repaired the leaking plumbing connections, replaced corroded components, and verified proper water flow and drainage. Documented the condition of existing pipes and repair work with photographs for record-keeping purposes.

Provided estimate for gas line installation to accommodate dryer conversion from electric to gas. Assessed basement infrastructure and determined routing for gas shut-off valve installation within six feet of appliance location. Identified existing gas supply lines in ceiling joists and confirmed accessibility for connection. Evaluated clearances behind appliance and verified adequate space for code-compliant gas line installation and shut-off valve placement.

# HVAC Install - Complete System Completed full installation of residential HVAC system including furnace air handler and through-wall air conditioning unit in basement mechanical room. Installed new air handler unit on elevated wooden platform with proper clearances and mounted gray metal plenum cabinet for air distribution. Configured complete PVC condensate drain system with U-trap configuration and installed condensate pump with black discharge line for proper drainage management. Ran flexible ductwork connections to integrate with existing distribution system. Installed electrical disconnect box and completed all power connections to code requirements. Mounted electrical panel with digital controls on plywood backing for system operation. Routed all refrigerant lines, condensate piping, and electrical conduit in organized manner along concrete block walls. Verified all connections, tested system operation, and confirmed proper drainage flow through condensate management system.

Completed scheduled MVP cooling maintenance visit on 7-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified proper clearance around equipment despite dense surrounding landscaping, and confirmed unit operational status. All components functioning within normal parameters at time of service.

Responded to service call for outdoor lighting installation and repair of damaged wiring. Upon arrival, located outdoor electrical junction box containing timer control system with multiple circuit wires that had been accidentally severed. Assessed the damaged conductors, stripped and reconnected affected wiring using appropriate wire connectors, and verified proper circuit continuity. Successfully installed new outdoor light fixture and tested all connections to ensure safe operation of both the lighting system and existing timer-controlled equipment.

Responded to service call for leaking bathroom faucet. Upon arrival, inspected three-handle tub faucet fixture with chrome handles and central spout. Identified source of leak and performed necessary repairs to stop water dripping. Tested all three handles and spout for proper operation and verified complete seal with no further leakage detected upon completion.

Completed MVP recurring cooling maintenance visit on outdoor air conditioning condenser unit. Performed thorough inspection of heat exchanger coil, noting visible cleaning patterns on finned surfaces, and documented current condition of compressor motor, electrical connections, and mounting components. Unit showed normal weathering consistent with outdoor installation; photographed equipment condition and surrounding area for maintenance records.

Responded to service call for furnace displaying 4 red blinks followed by 2 blinks error code and condensation issues on AC unit and ductwork. Upon inspection, found outdoor condenser unit with heavily soiled coil fins showing significant dirt, pollen, and environmental debris accumulation with greenish discoloration. Air filter on unit exhibited extreme clogging with brownish-gray particulate matter throughout pleated sections, severely restricting airflow. Diagnosed condensation on ductwork as result of inadequate airflow causing temperature differential and moisture accumulation. Documented equipment condition through photographs showing Trane condenser unit requiring cleaning and maintenance. Recommended immediate coil cleaning, filter replacement, and airflow restoration to resolve error codes and eliminate condensation problems affecting system performance.

Responded to outdoor spigot malfunction with severe leaking and hose connection seized onto threaded outlet. Successfully removed stuck hose fitting from brass hose bib, inspected valve assembly and threading for damage, and restored proper operation of the cross-handle valve to eliminate water loss.

# HVAC Maintenance - Cooling Service Completed Performed comprehensive MVP cooling maintenance visit on 15-year-old residential air conditioning system. Conducted thorough inspection of outdoor condenser unit, verifying proper operation of fan motor and compressor. Examined condenser coil condition through louvered side panels and confirmed adequate airflow through unit. Inspected refrigerant line set and electrical connections at outdoor unit, ensuring all connections were secure and properly insulated. Accessed indoor control panel to evaluate electrical components and system controls. Inspected circuit board assembly, terminal blocks, relays, and associated wiring connections for signs of wear, overheating, or deterioration. Verified all wire terminations at terminal strips were tight and properly secured. Examined control board components and electrical infrastructure for proper operation. Confirmed system safety controls and electrical disconnect were functioning correctly. Uni

Completed MVP cooling maintenance visit on 3-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including visual assessment of coil condition, cabinet integrity, and proper airflow clearance. Cleaned exterior grilles which showed moderate dirt accumulation and grime buildup. Verified unit levelness and checked refrigerant line connections. Inspected condensate drain pan for proper operation and cleared surrounding vegetation to maintain adequate clearance for optimal performance.

Completed comprehensive AC tune-up maintenance on two residential cooling systems—one approximately one year old and the other ten years old. Performed standard preventive maintenance procedures including inspection of electrical components, capacitors, contactors, and condenser units; verified proper system operation and efficiency on both units. Installed complimentary carbon monoxide detector as part of service package.

Completed installation of new air conditioning system with matching evaporator coil, achieving 90% furnace efficiency rating. Replaced dual electrical contactor assembly showing oxidation damage and installed new condenser unit on concrete pad. System tested and verified operational with proper refrigerant charge and airflow confirmed through diagnostic equipment.

Responded to service call for plumbing and gas line work. Assessed corroded water supply lines at utility sink location and capped off existing gas line to accommodate conversion from gas to electric dryer. Inspected aged plumbing infrastructure including shut-off valves, supply manifold, and copper piping connections. Completed gas line termination per code requirements to ensure safe installation of new electric appliance.

Performed comprehensive preventive maintenance on residential air conditioning system less than one year old. Conducted thorough inspection of outdoor condensing unit, verified proper operation of compressor and fan motor, checked refrigerant levels and system pressures within manufacturer specifications. Cleaned condenser coils and heat exchanger fins to remove accumulated dirt and debris, ensuring optimal heat transfer efficiency. Inspected all electrical connections, contactors, and capacitors for proper operation. Verified drainage system functionality and cleared condensate lines. Unit operating normally with no deficiencies noted at time of service.

Installed whole home automatic water shut-off system with Moen smart control unit on main water line. Replaced existing shut-off valve and associated fittings with new brass connections and copper pipe sections to accommodate the electronic leak detection and automatic shut-off device. Coordinated with electrical contractor for dedicated outlet installation near water meter to power the system, ensuring proper integration of the automated water protection equipment.

Installed electrical outlet near water meter in unfinished basement utility area to support plumbing work requirements. Outlet was wired using truck stock materials and positioned for convenient access to water meter location. Work was coordinated with related plumbing project to ensure proper sequencing of trades.