Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Responded to service call for inefficient Verne brand tanked water heater at 32-year-old residential property. Upon inspection, determined existing tank-style unit had reached end of service life and recommended replacement with high-efficiency tankless system. Removed old tanked water heater and installed new Rinnai tankless water heating unit on basement wall with proper clearances and ventilation. Connected copper supply lines, installed expansion tank with isolation valves, and ran new gas line to unit. Mounted exterior PVC vent termination through foundation wall above grade with appropriate flashing and weather protection. Installed electrical service and control panel with indicator lights. Tested all connections for leaks, verified proper gas pressure, commissioned unit according to manufacturer specifications, and confirmed hot water delivery throughout home. System operating at optimal efficiency with significant energy savings compared to previous tank-style heater.

Completed installation of two Lennox outdoor condensing units with corresponding evaporator coils for a dual-zone residential HVAC system. Units were positioned side by side on vibration-dampening rubber pads against the exterior wall, with copper refrigerant lines and electrical conduits properly routed and secured to the building. Installed DiversiTech disconnect boxes with appropriate fusing for each unit to meet electrical code requirements. All refrigerant lines were brazed, insulated, and tested for leaks. System was evacuated, charged to manufacturer specifications, and tested for proper operation. Installation includes proper drainage provisions and meets all applicable building and electrical codes.

Completed new plumbing installation for sink drain and established electrical hookups for dishwasher, refrigerator, and ice maker as part of ongoing home renovation. Installed PVC drain stub-out through tile flooring and coordinated rough-in work with existing construction layout markings. Documented pre-existing conditions including wall damage and mold at baseboard level, and exposed electrical outlet requiring attention during renovation completion.

Responded to emergency electrical repair call for damaged wiring at commercial property undergoing foundation excavation work. Upon arrival, assessed electrical conduit and wiring that had been compromised multiple times during foundation waterproofing and drainage installation activities. The electrical line running along the exterior brick wall and into the excavation trench had become frayed and broken due to repeated contact with construction equipment and materials during the dig-out process. Repaired damaged electrical conduit and replaced compromised wiring to restore safe electrical service to the business facility.

Performed routine maintenance flush on a 7-year-old tankless water heater unit. Descaling solution was circulated through the system using bucket and pump setup to remove mineral buildup and ensure optimal heat exchanger performance and efficiency.

Responded to service call for gas meter that was removed during wall maintenance and became twisted during reinstallation. Upon arrival, assessed the exterior-mounted natural gas meter installation and confirmed the meter assembly had been improperly repositioned. Carefully untwisted the gas meter piping to restore proper alignment and orientation of the meter body and connecting lines. Reattached and secured the meter assembly to the exterior wall mounting bracket, ensuring all pipe connections were properly aligned with both the building supply lines and the curved riser pipes. Verified all connections were secure and the meter was level and stable on its mounting stand. Inspected the complete installation including the horizontal supply piping and vertical connections to confirm proper positioning and no stress on joints or fittings.

Completed MVP recurring cooling maintenance visit on Goodman brand outdoor condensing unit. Performed standard system inspection, documented equipment condition with photographs showing unit operating properly with clean coil fins, secure electrical connections at wall-mounted disconnect, and adequate clearance from surrounding landscaping on concrete pad. All components functioning within normal parameters at time of service.

Redid outdoor PVC condensate drain terminations for HVAC system. Reconfigured drain line piping with proper P-trap formation extending from exterior wall to ensure adequate drainage and code compliance.

Performed comprehensive preventive maintenance tune-up on 10-11 year old residential air conditioning system. Inspected condenser unit exterior, noting significant debris accumulation on coil surfaces requiring attention. Completed standard seasonal maintenance procedures to prepare system for cooling season operation, documenting equipment condition through photographic documentation of outdoor unit installation and filter/coil surfaces showing heavy dirt buildup from extended service period.

# HVAC Service - Furnace Responded to service call for 5-year-old gas furnace with water accumulation underneath unit. Performed diagnostic inspection of furnace components including blower motor assembly, condensate drainage system, and internal housing. Documented equipment condition with photographic evidence showing motor mounting configuration, wiring harness routing, and mechanical compartment layout for service records.

Replaced defective outdoor thermostatic expansion valve (TXV) on HVAC system under warranty coverage. System was evacuated, new brass TXV installed with proper torque specifications on copper line connections, and recharged with 8 pounds of R-454B refrigerant to manufacturer specifications.

Completed installation of outdoor air conditioning condenser unit and matching evaporator coil as part of a secondary AC system installation. Unit was positioned on concrete pad with proper clearances, secured to manufacturer specifications, and connected to electrical disconnect box via conduit. Refrigerant lines were properly insulated and routed from the outdoor condenser to the indoor coil, with all connections brazed and pressure tested for leaks. System was evacuated, charged with refrigerant to manufacturer specifications, and tested for proper operation including airflow, temperature differential, and electrical draw verification. All installation met local code requirements and manufacturer guidelines for optimal performance.

Completed comprehensive maintenance visit on three-year-old MVP air conditioning system. Performed thorough inspection of air handler unit, condensate drain lines, and filtration system. All components found operating within normal parameters. System shows appropriate wear for age with clean filter media and properly functioning drainage. Based on equipment age and previous service history, recommended enrolling in preventative maintenance agreement to ensure continued optimal performance and extend system lifespan.

Completed comprehensive heating maintenance inspection on residential HVAC system located in attic space. Serviced and inspected Aprilaire whole-home dehumidification unit, verifying proper operation of all mechanical components, refrigerant lines, and electrical connections. Examined gas valve assembly with SGA416 actuator, checking for proper function and secure mounting on supply line. Verified condensate drainage system with white PVC piping for proper flow and clearance. Inspected copper refrigerant lines, brass fittings, and service valves for signs of leaks or deterioration. All equipment found operating within normal parameters with no immediate service concerns identified.

Performed scheduled maintenance on a 6-year-old Generac 11-12kW standby generator. Inspected engine components, checked fluid levels, examined radiator and cooling system for proper operation, and verified all electrical connections were secure. Unit tested successfully and left in proper working condition.

Responded to service call regarding natural gas odor detected when furnace had been idle for several days. Performed comprehensive safety inspection of gas valve assembly, burner components, and all gas connections. Inspected blower motor, electrical connections, and wiring harnesses for proper operation. Conducted leak detection testing on gas valve, manifold connections, and supply lines. All components found to be functioning within normal parameters with no active gas leaks detected at time of inspection. Advised customer on proper system operation and recommended monitoring for any recurring odor issues.

Installed new electrical line in 10-year-old residential property, routing wiring through attic crawl space alongside existing HVAC ductwork and structural framing. Work included running cable along wooden beams to designated termination point, installing electrical panel with cover plate in utility area, and ensuring proper clearances from metal ductwork per code requirements.

Completed MVP cooling maintenance visit on residential Lennox air conditioning system. Performed standard inspection of outdoor condenser unit, verified proper installation of refrigerant lines and electrical connections, and documented equipment condition with no visible deficiencies noted. Unit operating normally with all components functioning as designed.

Completed BS-MVP recurring heating maintenance visit on residential HVAC system. Performed comprehensive inspection of air handler unit and internal components including blower motor, electrical connections, refrigerant lines, and gas valve assembly. Documented system condition with interior and exterior photographs showing all major components operating within normal parameters. All wire connections, ductwork, and mechanical assemblies verified secure and functioning properly.

Responded to service call for leaking shutoff valve located under upstairs bathroom sink in 30-year-old residence. Upon arrival, confirmed constant leak at shutoff valve assembly. Replaced faulty shutoff valve with new quarter-turn angle stop valve, ensuring proper seal and connection to supply line and fixture tailpiece. Tested system for leaks, verified proper operation, and restored water service to bathroom sink.