Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Performed site evaluation for mini split installation in new addition under construction. Assessed framing configuration, wall cavity dimensions, and electrical routing requirements. Documented interior rough framing with exposed studs, OSB sheathing, and preliminary electrical runs to determine optimal placement for indoor air handler unit and refrigerant line penetrations. Evaluated structural considerations and clearance requirements for equipment mounting and future finish work coordination.

Rewired basement electrical circuit to separate two outlets from switch control, making them continuously powered while maintaining switch operation for room lighting. Traced existing wiring through basement ceiling joists, disconnected outlet hot leads from switch leg, and connected them directly to constant power source. Verified proper circuit operation, tested all outlets for correct voltage and polarity, and confirmed light switch continues to control room fixtures independently.

Completed scheduled MVP heating maintenance visit on Rheem furnace system. Performed comprehensive diagnostic inspection of all internal components including burner assembly, heat exchanger, blower motor, electrical connections, and control board using Fieldpiece testing equipment. Verified proper operation of all mechanical and electrical systems, checked wire connections and terminal blocks for secure contact, and confirmed unit functionality. All components found to be in good working condition with no issues identified during inspection.

Responded to report of repeatedly tripping basement GFCI outlet feeding downstream circuits and non-functional outdoor outlets. Inspected basement GFCI receptacle mounted on wooden backing near appliance area, noting visible water staining on adjacent wall surfaces indicating potential moisture intrusion. Tested GFCI functionality and load circuits, traced wiring connections to exterior outlet locations. Replaced faulty basement GFCI receptacle with new tamper-resistant unit, verified proper wiring connections and grounding. Confirmed restoration of power to all downstream outlets including exterior receptacles. Advised customer of moisture concerns observed near electrical components and recommended monitoring for future water infiltration issues.

Responded to no heat call on 12-year-old furnace with history of operational issues following previous air conditioning installation. Upon inspection, discovered failed electrical connector with exposed wiring at blower motor assembly, along with significant corrosion and debris accumulation on mounting brackets and copper refrigerant lines. Replaced damaged wire connector, cleaned corroded components, and verified proper blower motor operation. Tested system through complete heating cycle and confirmed furnace now operating within normal parameters.

Troubleshot and repaired a non-functional electrical outlet on the front porch by identifying the source of power loss and restoring proper electrical supply. Installed a new dedicated 240-volt circuit in the basement with an approximately 8.5-foot conduit run through the open ceiling area, terminating at a receptacle mounted to the concrete block wall in the same room as the main electrical panel. All work was completed to code specifications with proper wire sizing, circuit protection, and secure mounting methods.

Installed macerating toilet system in basement laundry room between existing sump pump and dryer. Tapped into main CPVC water line and ran new water supply line down wall, terminating with angle stop and supply line connection. Connected macerator discharge and vent into existing washing machine ABS drain pipe at laundry tub location. Coordinated with electrical contractor to install dedicated outlet for macerator pump operation. Customer supplied toilet bowl for installation on macerator tank unit.

Completed toilet repair by removing and replacing the existing wax ring seal and installing a new water supply line. Upon arrival, accessed the toilet shutoff valve, disconnected the old supply line, and removed the toilet from the floor flange. Scraped away the deteriorated wax ring, cleaned the flange surface, and inspected for any damage or additional issues. Installed new wax ring seal and repositioned toilet, ensuring proper alignment and secure mounting. Connected new braided stainless steel supply line to both the shutoff valve and toilet tank fill valve, tested for leaks, and verified proper water flow and tank refill operation.

Completed preventive maintenance on an 11-year-old furnace system. Inspected air filter showing moderate dust accumulation and verified proper fit within housing, noting minor corrosion on metal ductwork frame. Examined internal electrical components, wiring connections, and mechanical assemblies, confirming all connections secure and system operational.

Completed comprehensive furnace maintenance per MVP protocol, including inspection of all electrical connections, wiring harnesses, and control components. Verified proper operation of evaporator coil assembly, Aprilaire humidifier control system, and all associated ductwork connections throughout the system.

Completed fall tune-up on 7-year-old Lennox gas furnace. Performed standard maintenance including heat exchanger inspection, burner assembly cleaning, and system diagnostics. Unit operating within normal parameters with all components functioning properly.

Performed startup and commissioning on newly installed air handler and add-on air conditioning system following completion of electrical work. Conducted system diagnostics using digital gauges to verify proper refrigerant pressures, temperatures, and airflow parameters, confirming all equipment is operating within manufacturer specifications and warranty requirements are met.

Completed comprehensive maintenance on both air conditioning and furnace systems during scheduled morning appointment. Performed system diagnostics using calibrated digital manifold gauge to measure refrigerant pressures and verify proper cooling system operation. Inspected control board components including DIP switch configurations and circuit board connections to ensure proper system communication and functionality. All equipment operating within manufacturer specifications upon completion of preventive maintenance procedures.

Replaced failed FB40T12/Supreme fluorescent bulb in kitchen ceiling light fixture. Parts were ordered and received prior to service visit. Fixture is now fully operational and providing proper illumination.

Completed 200-amp main electrical panel replacement with full service upgrade in accordance with 2023 National Electrical Code requirements. Installed new panel board, exterior disconnect, and 15 feet of 4/0 SER cable to bring system into compliance with current code standards. All circuit breakers properly configured, wiring organized and terminated, and system tested for proper operation.

Completed comprehensive HVAC maintenance tune-up on 2-year-old Lennox system including both cooling and heating components. Performed full AC tune-up on Lennox WT 12-2034 outdoor unit, inspecting refrigerant lines, electrical connections, and verifying proper operation of control board and DIP switch settings. All system components operating within manufacturer specifications with no deficiencies noted.

Replaced leaking 2018 40-gallon tall water heater with new Bradford White 40-gallon tall unit featuring 10-year manufacturer warranty. Installed new shut-off valve and expansion tank tee due to proximity constraints at top of tank, added required bonding wire for code compliance, and included 4-year extended warranty coverage with maintenance value plan.

Completed scheduled MVP cooling maintenance visit. Inspected outdoor disconnect box and verified proper operation of electrical components, fuses, and circuit protection devices. Examined air filtration system and documented condition of pleated filter and pre-filter mesh, noting normal dust accumulation consistent with system usage.

Responded to service call for non-functioning garage GFCI outlet and inoperative basement recessed lighting. Troubleshot garage outlet circuit after previous GFI and breaker reset attempts proved unsuccessful; diagnosed wiring fault and restored power to GFCI receptacle. Investigated basement lighting issue where two of three can lights on single switch remained non-operational despite bulb replacement; identified potential cam mechanism failure or circuit wiring defect requiring further investigation.

Completed scheduled maintenance on 6-year-old air conditioning system and 1-year-old furnace. Inspected evaporator coil assembly, which showed normal condensation buildup during operation, indicating proper cooling function. Verified refrigerant lines, fin spacing, and overall system cleanliness with no issues identified.