Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Completed scheduled maintenance on 6-year-old air conditioning system and 1-year-old furnace. Inspected evaporator coil assembly, which showed normal condensation buildup during operation, indicating proper cooling function. Verified refrigerant lines, fin spacing, and overall system cleanliness with no issues identified.

Performed comprehensive tune-up on 3-year-old Carrier gas furnace unit located in basement utility room. Conducted full system inspection, verified proper operation of all components, inspected and documented air filter condition, and confirmed unit is operating within manufacturer specifications for the heating season.

Performed scheduled maintenance on residential Generac standby generator unit. Conducted comprehensive inspection of internal components including engine, fuel system, coiled hoses, and mechanical assemblies. Verified proper operation of all systems, checked PVC exhaust piping connections and mounting integrity, and confirmed unit remains in good working condition for reliable backup power service.

Completed comprehensive tune-up on 15-year-old furnace system per customer's request for after 3PM service. Performed thorough inspection of heat exchanger assembly, verified structural integrity of aluminum tubes and junction connections, and confirmed proper seating of all fasteners. Inspected control board wiring harnesses, verified secure connections of all electrical bundles, and confirmed proper voltage at circuit boards. All components found to be in functional condition with normal wear appropriate for unit age, system tested and operating within manufacturer specifications.

Responded to low water pressure complaint regarding DAB Esybox mini booster pump installed approximately three months prior. Customer reported inadequate performance affecting in-ground sprinkler system operation. Upon arrival, conducted visual inspection of exterior booster pump installation and associated PVC piping configuration. Verified mounting hardware and backflow preventer assembly condition. Checked system pressure gauge readings and evaluated pump performance parameters. Inspected brass fittings, compression connections, and valve assemblies for proper operation. Assessed pump control settings and pressure switch calibration. Documented current system configuration with photographs showing exterior wall-mounted installation and pressure gauge assembly. Verified electrical connections and pump cycling operation. System evaluation completed to determine cause of reduced water pressure and diminished sprinkler performance compared to initial installation standards.

Completed scheduled contract maintenance on a residential furnace approximately 2 years old. Performed comprehensive tune-up service including visual inspection of all interior components, electrical connections, and control systems. Verified proper operation of blower motor assembly, examined all wire harnesses and connections for signs of wear or damage, and confirmed circuit board functionality. Inspected PVC venting connections, refrigerant lines, and all mechanical components within the cabinet. All systems found operating within normal parameters with no deficiencies noted. Unit is in excellent condition with maintenance protection valid through 2026.

Responded to water leak complaint on 2-year-old Lennox AC unit (EL18XCV-036-230A03). Found condensate catch basin malfunctioning, causing water to discharge from overflow pipe onto floor. Inspected condensate drain system including PVC drainage lines and internal catch pan. Cleared blockage in primary drain line, verified proper pitch and flow through condensate piping, and tested safety float switch operation. Confirmed unit cycling properly with condensate draining correctly through primary line without overflow. System returned to normal operation with no further water leakage observed.

Completed MVP cooling maintenance visit on HVAC system. Performed system inspection, checked air filter condition and airflow, and measured static pressure readings using digital manometer which indicated 0.73 inches of water column. Verified proper operation of blower motor, inspected electrical connections and wiring, and confirmed condensate drainage system functioning correctly.

Completed comprehensive MVP Cool maintenance on an 18-year-old outdoor condensing unit. Performed standard preventive maintenance procedures including inspection of fan motor operation, electrical connections, and refrigerant lines. Unit showing age-appropriate wear with weathering on exterior housing and surrounding vegetation requiring clearance for proper airflow and accessibility during future service visits.

Responded to service call for leaking tanked water heater. Upon inspection, confirmed active leak from residential water heater requiring replacement. Documented existing plumbing configuration including copper supply lines, expansion tank, and associated safety equipment including carbon monoxide detector in mechanical room.

Responded to no-heat call on 10-year-old furnace. Upon arrival, performed diagnostic inspection of gas furnace system. Accessed interior components and conducted visual inspection of all major assemblies including blower motor, control board, wiring connections, and burner assembly. Inspected burner assembly and confirmed proper flame ignition pattern with characteristic blue flames across burner rack. Verified gas valve operation and examined all electrical connections throughout the unit, including wire harnesses, connectors, and wire nuts for signs of looseness, corrosion, or damage. Checked control board for proper function and examined all safety switches and limit controls. Tested system operation and confirmed furnace successfully ignited and cycled properly. System now heating normally with all components functioning as designed. Unit returned to full operational status.

Completed installation of a new black finished flange assembly for the garbage disposal unit. The replacement flange was installed on the stainless steel sink basin, securing the Badger disposal unit connection. Work included proper sealing and mounting of the disposal flange to ensure leak-free operation.

Completed scheduled maintenance on 13-year-old gas heating system. Performed electrical diagnostics using clamp meter to verify proper amperage draw and tested capacitor functionality, which measured 76.53 microfarads and within acceptable operating range. All components inspected and system operating normally with no immediate service needs identified.

Inspected 7-8 year old electric water heater reported as non-functional. Upon arrival, found extensive rust-colored corrosion staining running vertically down the front of the tank, with visible moisture damage on the concrete floor surrounding the base of the unit. The water heater exhibited signs of tank failure with standing water present beneath the unit. Documented the condition of the failed water heater with photographs showing the deteriorated state of the tank, corroded exterior, and water damage to the surrounding area. Provided free estimate for complete water heater replacement.

Excavated and cleaned trench around above-ground pool perimeter in preparation for electrical inspection. Documented all electrical connections with photographs showing exposed conduit and wiring installations. Coordinated with inspector onsite and completed backfill of trench following successful inspection approval.

Installed two new dedicated 120V circuits for exterior holiday decoration outlets. First circuit was run from the basement subpanel to a new weatherproof receptacle mounted near the front of the home at foundation level. Second circuit was installed from the main electrical panel to a new exterior outlet positioned just inside the fence line near the garage area. Both circuits were wired with appropriate gauge copper conductors, protected with GFCI breakers, and terminated in weather-resistant outlet boxes with in-use covers mounted on the exterior brick foundation. All work completed to current NEC standards for outdoor receptacle installations.

Performed comprehensive HVAC maintenance including thorough cleaning of the squirrel cage blower wheel to remove accumulated dust and debris, cleaned the indoor evaporator coil, and completed full heating system maintenance. No parts replacement was required to restore the system to optimal operating condition.

Completed maintenance value plan heating inspection on two furnace systems. Performed comprehensive system diagnostics using digital manifold gauges to verify proper refrigerant pressures and operational parameters. Inspected all refrigerant line connections, mounting hardware, and interior cabinet components for both units, confirming secure copper line installations and proper fastening. All systems operating within normal specifications with no deficiencies noted.

Completed replacement of two 90% AFUE furnaces at residential property. Both units were successfully installed with new exterior PVC intake and exhaust venting terminations visible on the home's exterior walls. All venting was properly sealed, secured, and positioned according to manufacturer specifications and local building codes to ensure safe operation and optimal efficiency.

Completed electrical estimate for Kohler generator installation requiring propane fuel source. Assessed existing dual-meter residential electrical service with Landis+Gyr and Milbank meters, documented current panel configuration including main distribution panel with multiple circuit breakers and two additional sub-panels mounted on OSB backing board in basement utility area. Evaluated electrical infrastructure, conduit routing, and available space to determine generator integration requirements and transfer switch placement for seamless backup power system installation.