Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Completed annual heating maintenance tune-up on furnace per maintenance agreement. System was operating properly upon arrival. Performed comprehensive inspection of heating equipment, including examination of blower motor, heat exchanger, gas connections, and condensate drainage system. Verified proper operation of all mechanical and electrical components, confirmed adequate airflow, and ensured all safety controls functioning correctly. System left in optimal working condition.

Replaced existing pressure reducing valve (PRV) and installed new 3/4"x3/4"x1/2" tank tee with tankless-style expansion tank to regulate water pressure and accommodate thermal expansion in the system. Work required careful handling due to existing polybutylene 3/4" supply line running to water manifold. Installation included brass fittings, pressure gauge, and black expansion tank mounted within wall cavity access panel, with all components tested and verified operational upon completion.

Replaced damaged exterior electrical conduit running from meter box to main electrical panel. Installed new PVC conduit pipe with proper couplings and mounting straps, then pulled and terminated new circuit wiring to restore safe electrical service to the panel.

Performed routine maintenance flush on a Bradford White 40-gallon natural gas water heater (Model RG240S6N). Drained sediment buildup from tank, flushed system to remove mineral deposits, and verified proper operation of temperature and pressure relief valve. Unit is functioning within normal parameters for a 9-year-old home installation.

Completed hot water tank flush and fill service on the residential water heating system. Upon inspection, the unit was a Rinnai tankless water heater, not a traditional tanked system, so maintenance procedures were adjusted accordingly. Performed standard maintenance including system inspection, verified proper venting through white PVC intake and exhaust pipes, checked copper water line connections and shut-off valves for proper operation, and confirmed unit functionality through the digital control panel.

Responded to service call for upstairs toilet leaking into ceiling below. Upon arrival, performed diagnostic inspection of toilet and surrounding plumbing fixtures. Inspected toilet tank internal components including fill valve assembly with red cap, flush valve mechanism, and associated supply lines. Examined flexible braided stainless steel supply line connection from wall-mounted shut-off valve to toilet. Identified source of water leak and documented conditions with photographs. Completed diagnostic evaluation of plumbing system to determine cause of ceiling leak and necessary repairs.

Conducted electrical estimate for generator installation. Evaluated existing electrical panel configuration and circuit breaker arrangement to determine compatibility and capacity for generator integration. Assessed site conditions including available space for equipment placement and confirmed no homeowner association restrictions would impact installation.

Completed installation of new sump pump system in unfinished basement area. Installed pump unit with proper discharge piping, including vertical PVC discharge line secured to wall studs with mounting clips, and connected all necessary plumbing components to ensure effective water removal from the basement space.

Completed scheduled MVP heating maintenance visit. Performed diagnostic testing on HVAC control system using digital multimeter, recording voltage readings at 5.94V on system wiring and control board connections. Inspected circuit board components including integrated circuits, relay assemblies, and air sensor terminal connections to verify proper operation and system functionality.

Replaced fluorescent light tubes in kitchen ceiling fixtures. Customer had replacement bulbs available but was unable to access the ceiling-mounted fixtures due to height limitations. Removed existing Philips F40T12/CW 40-watt fluorescent tubes from recessed ceiling fixtures and installed new tubes provided by customer. Verified proper operation of all fixtures upon completion.

Responded to service call for AC condenser causing lights to flicker when unit cycles on. Upon arrival, found outdoor condensing unit heavily overgrown with tall grasses, weeds, and vegetation that had accumulated around and through the equipment, indicating extended period of neglect. Cleared excessive vegetation from around unit to restore proper airflow and access for inspection.

Conducted installation inspection of residential furnace system and identified code violation with exhaust venting materials. The cellular core PVC piping currently installed for the furnace exhaust vent does not meet manufacturer specifications and approval requirements. Documented the non-compliant venting configuration with photographs showing both exterior termination point and interior mechanical room installation. The white PVC vent pipe assembly extends from the furnace unit through the foundation wall with multiple 90-degree elbows terminating on the exterior gray vinyl siding. Installation has been placed on hold pending manager review and approval for corrective action to bring the system into compliance with manufacturer requirements and applicable codes.

Completed routine AC tune-up on 4-year-old Goodman condenser unit. Performed comprehensive system inspection including motor connections, electrical components, and condenser operation. All wiring connections secure, unit operating within normal parameters, no issues identified during maintenance check.

Completed comprehensive MVP AC maintenance on residential cooling system. Performed thorough inspection of outdoor condensing unit, verified proper operation of all mechanical and electrical components, and accessed control board to confirm system settings and diagnostics display functionality. Unit operating within normal parameters with all DIP switch configurations verified and system displaying proper diagnostic codes.

Performed MVP air conditioning maintenance on outdoor condensing unit. Inspected heat exchanger coil which showed significant accumulation of dirt, dust, leaves, and organic debris between fins, indicating extended service period without cleaning. Took electrical measurements using clamp meter, recording amperage readings of 27.7A and 25A to verify proper compressor and fan motor operation. Unit exhibited typical outdoor weathering patterns consistent with normal exposure conditions.

Completed MVP cooling maintenance on residential HVAC system. Performed comprehensive inspection of electrical components including capacitor, wiring connections, and relay assembly. Verified proper system operation through electrical testing using clamp meter to ensure all readings were within manufacturer specifications.

Installed customer-supplied doorbell system including mounting and wiring of new transformer to electrical panel. Connected transformer to dedicated circuit breaker, routed low-voltage wiring to doorbell location, and verified proper voltage output and functionality of complete doorbell system upon installation.

Completed scheduled heating maintenance on a 9-year-old natural gas furnace. Performed comprehensive system inspection including combustion analysis using calibrated digital analyzer. Verified optimal combustion efficiency at 98.0% with carbon monoxide levels reading 15 ppm, CO₂ at 59%, and stack temperature at 89°F - all within manufacturer specifications for safe and efficient operation. Inspected blower motor assembly, electrical connections, and internal components with access panel removed. Checked PVC venting system for proper installation and secure connections. All mechanical and safety systems operating as designed with no deficiencies noted.

Completed comprehensive maintenance on 3-year-old residential air conditioning system. Inspected outdoor condensing unit, verified proper installation on pad with adequate clearance, and investigated reported rattling noise at startup. All components found in good working condition with no visible damage or deterioration noted.

Responded to a clogged toilet service call and successfully cleared the obstruction using standard plumbing techniques. The toilet was restored to proper flushing operation, and the fixture was tested to ensure complete drainage and functionality before completing the service.