Trusted HVAC, Electrical & Plumbing Services in Streetsboro, OH

Completed preventive maintenance on residential air conditioning system. Inspected electrical connections at outdoor condensing unit, verified proper wire routing and terminations, and documented equipment condition. All electrical components found secure with no immediate safety concerns noted, though unit exterior shows normal weathering from environmental exposure.

Conducted comprehensive assessment of 28-year-old furnace and air conditioning system at owner-occupied residence for complete replacement estimate. Evaluated existing Carrier furnace installation, inspected condensate drainage lines, venting configuration, and electrical connections in basement utility area. Documented current system condition including aged refrigerant lines showing corrosion, existing ductwork connections, and overall equipment layout to provide accurate replacement specifications and installation requirements.

Responded to service call for furnace emitting burning odor with visible damaged component. Upon inspection, accessed unit interior and identified compromised electrical component on control board. Documented existing wiring configuration and component condition with photographs showing extensive wire harness network, control board connections, and internal mechanical assembly including blower motor housing and PVC condensate piping. Given household occupant's medical sensitivity to temperature fluctuations, prioritized rapid assessment and provided recommendations for component replacement to restore safe heating system operation.

Completed full HVAC system installation including an 80% efficiency furnace and air conditioning unit for an 858 square foot residential property. The AC condenser was positioned at the rear of the home per the site plan, with the furnace installed in the basement mechanical room alongside existing water heating equipment. New flexible ductwork was installed and connected to the furnace with proper insulation, and all gas connections were secured with appropriate shut-off valves for safety compliance.

Responded to electrical outage affecting approximately two-thirds of modular home that had been vacant for three and a half months. Upon arrival, conducted comprehensive evaluation of electrical system to identify cause of power loss suspected to be related to rodent damage from mouse infestation. Performed thorough inspection of main electrical panel and discovered extensive corrosion and water damage throughout the enclosure. Panel exhibited significant rust accumulation on bottom surfaces and lower portions, with corrosion extending to terminal connections and internal components. Found degraded and discolored wiring with compromised insulation showing signs of aging and environmental exposure. Observed disorganized and tangled wiring in lower section of panel with accumulated debris and particulate matter. Documented conditions with photographs showing corroded bussing connections, deteriorated circuit breakers, and moisture-damaged electrical components. Panel condition indicate

Returned to property to install replacement thermostat on furnace unit that was previously installed approximately two weeks prior. Successfully mounted and wired new Honeywell digital thermostat to wall, verified proper communication with heating system, and confirmed operational functionality.

Performed routine preventive maintenance on residential standby generator system. Conducted comprehensive inspection of unit including visual assessment of gas meter connections, supply piping, and associated fittings which showed signs of corrosion on copper components. Verified generator control panel operation with all indicator lights functioning properly and confirmed unit powers on successfully. Documented existing condition of gas supply infrastructure and generator equipment with photographic records for service history.

Completed installation of new air conditioning system and humidifier at residential property. Installed outdoor condenser unit on prepared mulch bed with proper clearances, ran refrigerant lines and electrical conduit to disconnect box mounted on exterior wall, and installed condensate drain line. System was evacuated to proper micron level as verified by vacuum gauge reading, pressure tested, and commissioned for operation.

Responded to service call for a leaking Rheem Performance 40-gallon gas water heater (Serial # A421906493). Upon inspection, confirmed active leak at base of unit with visible water staining on concrete floor. Evaluated unit per previous diagnosis from another contractor indicating failed gas control valve and pilot assembly. Assessed overall condition of water heater and documented existing plumbing connections including copper supply lines, flexible connectors, and temperature/pressure relief valve. Provided technical evaluation and repair recommendations to customer.

Completed scheduled maintenance flush on tankless water heater unit mounted in basement utility area. Performed descaling procedure by isolating unit with service valves, circulating cleaning solution through heat exchanger to remove mineral buildup, and flushing system thoroughly to restore optimal performance and efficiency.

Completed comprehensive AC tune-up including system inspection and performance verification. Inspected and documented electrical components, including 30-amp FLNR fuses in holder, confirming proper amperage rating and fuse integrity for system protection. All components found operating within normal parameters with no immediate service needs identified.

Completed full HVAC system installation including 80% AFUE gas furnace with associated ductwork, electrical connections, and refrigerant line sets. Installed and configured all necessary components including blower motor assembly, gas line connections, condensate drain system, copper refrigerant piping, and electrical service with dedicated circuit. System tested and verified operational with proper airflow and safety controls functioning as designed.

Completed comprehensive air conditioning tune-up service during early morning appointment. Performed standard maintenance inspection including air filter examination, electrical component verification, and system operational check. All wiring connections, capacitor, and contactor were inspected and found to be in proper working condition with no immediate service needs identified.

Completed MVP heating maintenance visit per recurring service agreement. Performed standard heating system inspection, including examination of internal components, mounting hardware, gas lines, and blower assembly. Customer requested air conditioning service to be scheduled separately.

Completed comprehensive furnace tune-up on 2-3 year old heating system, including full operational testing, safety checks, and component inspection. Replaced 20x25x4 Filtrete air filter to ensure proper airflow and system efficiency. Performed requested operational check of air conditioning system to verify functionality ahead of cooling season.

Completed MVP Cooling Visit maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, cleaned protective metal grille guards that showed dirt and debris accumulation, and verified proper operation of all components. Confirmed electrical connections, refrigerant line integrity, and overall system functionality with unit operating within normal parameters.

Completed routine furnace tune-up and system inspection as scheduled. Inspected and evaluated existing air filter condition, which showed moderate dust accumulation and debris buildup requiring attention. Accessed HVAC filter housing unit and performed standard maintenance procedures to ensure optimal system performance and air quality for the heating season.

Performed scheduled A/C system maintenance which included inspection and cleaning of the blower wheel assembly that showed significant dust accumulation on the fan blades. Checked the furnace unit connections, PVC ventilation piping, and electrical components for proper operation and safety compliance, ensuring optimal system performance for the cooling season.

Performed routine MVP heating maintenance service. Inspected heat exchanger and coil assembly for proper condition, finding components clean and free from corrosion. Conducted electrical diagnostic testing with clamp meter, verifying proper amperage readings of 0.75A and voltage of 26.2V at control board, confirming system is operating within manufacturer specifications.

Responded to no-heat call for Goodman gas furnace. Inspection revealed faulty flame sensor as the root cause. Removed, cleaned, and reinstalled flame sensor electrode, restoring proper ignition and heat function.