Air Conditioning, Heating, Electrical & Plumbing Services in Uniontown, OH

Performed routine maintenance on 4-year-old gas furnace. Inspected and confirmed proper installation of clean pleated air filter. Used hex key tool to complete necessary adjustments during the service visit.

Responded to service call for a main drain backup in basement. Successfully snaked the main drain cleanout, clearing the blockage and restoring proper drainage. Documented condition of the cleanout access point and interior pipe threading which showed signs of sediment buildup and residue.

Performed comprehensive furnace and air conditioning tune-up as requested by customer. Inspected and replaced dirty air filter with significant dust accumulation. Used specialized tools to access and service internal components, ensuring optimal system performance and efficiency for both heating and cooling units.

Performed routine maintenance service on a Generac generator system. Inspected and verified proper operation of key components including hoses, wiring connections, and mounting hardware. Noted minor condensation on interior panels which is within normal operating parameters.

Performed scheduled MVP Heating Visit maintenance service, inspected system and replaced severely clogged air filter which showed significant dust accumulation throughout the pleated surface. Used diagnostic probe to verify proper system operation after filter replacement.

Completed annual maintenance service on a 2023 model tanked water heater in a 63-year-old home. Performed comprehensive system flush to remove sediment buildup and inspected all connections, valves, and temperature settings according to manufacturer specifications. No issues were identified during maintenance; system is operating at optimal efficiency with properly functioning temperature and pressure relief valve.

Performed comprehensive heating maintenance and AC tune-up, including inspection of control system circuit board connections and heating elements. Identified and documented water damage beneath refrigerant coils, checked valve integrity, and verified proper operation of all system components.

Completed warranty repair on HVAC system by replacing faulty inducer motor, pressure switch, and circuit board. Removed existing control board and installed new components to restore proper system functionality. All replacement parts were properly installed and system was tested to verify normal operation.

Responded to service call for 8-year-old Advance Platinum water heater making knocking noise during heating cycles. Upon inspection, determined sounds were consistent with sediment buildup in tank. Customer still has adequate hot water supply; recommended annual maintenance to extend unit life and reduce sediment-related noise.

Diagnosed and repaired a leaking toilet in a 65-year-old home, replacing worn internal tank components. Observed significant water damage and staining around the floor drain, indicating long-term leakage that had caused deterioration of the surrounding tile area. Completed full flush test after repair to verify proper operation and no further leakage.

Responded to no hot water call for natural gas water heater. Inspected unit and accessed control panel with electronic display. Diagnosed ignition system failure and restored proper operation of the water heater.

Completed installation of customer-supplied kitchen faucet with replacement of straight stops, snaked kitchen sink drain to clear backup, and replaced drain assembly with new basket strainer. Installed new PVC P-trap configuration under sink with proper connections to eliminate previous water staining/leakage issues observed during service.

Diagnosed and repaired malfunctioning temperature valve in shower/tub combination unit with brushed nickel fixtures. System now maintains consistent water temperature throughout operation, eliminating previous temperature fluctuation issues.

Performed scheduled MVP furnace maintenance service. Removed access panel for comprehensive inspection of internal components including blower motor, control board, and gas valve assembly. Inspected blower wheel and shaft for proper operation and condition, confirming system functionality.

Performed scheduled maintenance on furnace for MVP customer. Used TESLONG borescope to inspect internal components, revealing a circular perforated disc/wheel with signs of wear. Utilized Allen wrench to make necessary adjustments to mechanical elements during the service visit.

Conducted site assessment for generator installation, evaluating electrical panel and exterior wall for optimal placement of transfer switch and connection points. Proposed running dedicated line from main breaker panel to exterior wall for portable generator hookup, including necessary conduit, weatherproof connections, and code-compliant transfer mechanism.

Returned to complete scheduled UV bulb replacement in HVAC system. Successfully installed new UV bulb and performed system check to ensure proper operation. Verified electrical connections and control board functionality during service.

Responded to service call for kitchen sink clog. Inspected garbage disposal unit, which was properly connected to drain system with appropriate PVC drainage pipe and flexible waste line. Cleared obstruction and verified proper drainage function. Basement inspection revealed no issues with main drain lines or plumbing infrastructure.

Performed minimum viable product heat visit which included inspection of pipe connections and fittings. Conducted electrical testing with multimeter showing 16.2V reading on system components. Documented visible corrosion on metal surfaces and verified condition of insulation materials and flexible conduits.

Performed site assessment for replacement of existing natural gas water heater. Inspected exterior venting system and verified appropriate termination point. Examined interior plumbing connections including copper supply lines and valve assembly. Provided customer with installation options and scheduled future installation appointment.